Solution Solution to Repeating Notification of "[Gateway] was connected" Issue on ER605 V2 [Case Closed]
This Article Applies to:
ER605(UN)_V2_2.1.1 Build 20230115
ER605(UN)_V2_2.1.2 Build 20230210
Issue Description/Phenomenon:
Recently we received feedback that using ER605 V2 2.1.x firmware would cause repeating event notifications of "[Gateway] was connected" as below, and there might be a disconnected notification occasionally.
On Omada Controller:
On Omada App:
Related Posts:
Very lot messages to connect devices (Gateway)
ER605 Repeating Event Notifications On Omada App
Available Solutions:
Here is the current available solution to resolve the issue described in this thread.
Beta Firmware Download:
ER605(UN)_V2_2.1.2 Build 20230221 (Beta)
Please be sure you have read the Beta Test Agreement before proceeding!
Beta Release Note:
Fixed the repeating notification of "[Gateway] was connected" issue based on the official firmware 2.1.2_Build 20230210.
Feedback:
If this was helpful, welcome to give us Kudos by clicking the upward triangle below.
If there is anything unclear in this solution post, please feel free to comment below.
To submit a new different issue, please Start a New Thread for better assistance.
Thank you for your support and contribution in TP-Link Community!
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi @SeanieP
This is unusual. The MAC address belongs to Mercursys. Do you set up anything like IP-MAC binding or DHCP reservation?
In the firmware of V2.2.0, we have introduced a new feature that DHCP activities will be recorded in the log.
If you are running your whole network fine, then you don't have to worry about it. But this one seems unusual. Try a reboot and check settings. Would be helpful for us if you can check settings I mentioned above.
- Copy Link
- Report Inappropriate Content
@Clive_A yes I do use DHCP reservation. Should I select Mac binding? Can't understand why it keeps repeating the same notification. Network seems to be ok.
- Copy Link
- Report Inappropriate Content
Hi @SeanieP
That could relate to your reservation. You can consider either unbinding it and checking again or you can turn off this alert in Notifications.
The new controller added support to show the activities of the DHCP and every activity will be logged.
- Copy Link
- Report Inappropriate Content
@Clive_A Mac binding was off. I don't use a controller, only the router itself
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
After updating omada controller to the latest version, I have the same problem, there can be several thousand notifications per day
I am using
ER605 v2.0, Firmware Version:
2.2.0 Build 20230629 Rel.64012
Omada Controller 5.11.10
2.10.2 Build 20230704 Rel.64607
TL-SG2428P v1.0
1.1.8 Build 20230602 Rel.73473
EAP245(EU) v4.0
1.1.3 Build 20230224 Rel. 48254
- Copy Link
- Report Inappropriate Content
This is not always the same device, it happens with several.
My current firmware is 2.1.2 Build 20230313 Rel.41632
- Copy Link
- Report Inappropriate Content
Hi @SeanieP
If you don't run into any issues, then it is okay. The log system added a new feature for DHCP activities. You don't need to worry about issues if you don't run into problems.
As I explained earlier, new firmware added some features.
You can use a different level if you don't want to see certain logs.
- Copy Link
- Report Inappropriate Content
Please refer to the post above. Thanks for your understanding.
denis-odessit wrote
After updating omada controller to the latest version, I have the same problem, there can be several thousand notifications per day
I am using ER605 v2.0, Firmware Version: 2.2.0 Build 20230629 Rel.64012
Omada Controller 5.11.10
2.10.2 Build 20230704 Rel.64607
TL-SG2428P v1.0
1.1.8 Build 20230602 Rel.73473
EAP245(EU) v4.0
1.1.3 Build 20230224 Rel. 48254
- Copy Link
- Report Inappropriate Content
Information
Helpful: 5
Views: 10930
Replies: 50