Smart Home Community > Tapo Smart Switch > S200D goes to sleep
< Tapo Smart Switch

S200D goes to sleep

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

S200D goes to sleep

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
S200D goes to sleep
S200D goes to sleep
2025-05-29 17:48:57 - last edited 2025-06-09 11:33:41
Model: Tapo S200D  
Hardware Version:
Firmware Version:

S200D worked fine for several weeks.  Then one day it stopped working, and only did so if you pressed the smart button again a while later.  Once woken up it works fine, but after a while goes back to sleep.  This means I can't use it as an on/off switch for my device which requires immediate activation.  Any solutions to keep it on standby, or is it a faulty unit/battery?

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:S200D goes to sleep -Solution
2025-05-30 08:02:15 - last edited 2025-06-09 11:33:41

  @SYNT 

 

What are the specific symptoms of the issue? When the button enters 'sleep mode', do the automated rules it triggers fail to work? Do you need to press it once to 'wake' it up and then press it again (or double-click) for the automation to function correctly?

 

Check the signal strength of the sensor, such connectivity issues may occur if sensor's connection drops. >> Open Tapo app and go to sensor's Device Settings page, click Device Info, Tap the WiFi icon to see the signal strength (RSSI rate).

  • Strong: more than -50 dBm
  • Good to Average: among -70 dBm to -50 dBm
  • Poor: less than -70 dBm

 

You can also change a new battery, see if it helps. **Battery Type: CR2032

▶ Tapo P110M Matter 1.3 Release Energy Monitoring through Matter ▶ Smart HomeBase Tapo H500 - Even More Powerful Smart Hub ▶ First Smart Switch Module! Tapo S112 Smart Switch Module with Roller and Switch Dual Modes ▶ Tapo Camera Image Style & Image Brightness Try out a different image style for your camera!
Recommended Solution
  0  
  0  
#2
Options
1 Reply
Re:S200D goes to sleep -Solution
2025-05-30 08:02:15 - last edited 2025-06-09 11:33:41

  @SYNT 

 

What are the specific symptoms of the issue? When the button enters 'sleep mode', do the automated rules it triggers fail to work? Do you need to press it once to 'wake' it up and then press it again (or double-click) for the automation to function correctly?

 

Check the signal strength of the sensor, such connectivity issues may occur if sensor's connection drops. >> Open Tapo app and go to sensor's Device Settings page, click Device Info, Tap the WiFi icon to see the signal strength (RSSI rate).

  • Strong: more than -50 dBm
  • Good to Average: among -70 dBm to -50 dBm
  • Poor: less than -70 dBm

 

You can also change a new battery, see if it helps. **Battery Type: CR2032

▶ Tapo P110M Matter 1.3 Release Energy Monitoring through Matter ▶ Smart HomeBase Tapo H500 - Even More Powerful Smart Hub ▶ First Smart Switch Module! Tapo S112 Smart Switch Module with Roller and Switch Dual Modes ▶ Tapo Camera Image Style & Image Brightness Try out a different image style for your camera!
Recommended Solution
  0  
  0  
#2
Options

Information

Helpful: 0

Views: 273

Replies: 1

About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.