Home Network Community > Adapters > TX20UH gets real hot, packet loss, and high ping spikes even with it's latest driver
< Adapters

TX20UH gets real hot, packet loss, and high ping spikes even with it's latest driver

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TX20UH gets real hot, packet loss, and high ping spikes even with it's latest driver

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TX20UH gets real hot, packet loss, and high ping spikes even with it's latest driver
TX20UH gets real hot, packet loss, and high ping spikes even with it's latest driver
2025-06-03 12:30:10 - last edited 2025-07-07 01:58:02
Model: Archer TX20UH  
Hardware Version: V1
Firmware Version:

me 3 (I also have the same problem. I am now using T3U, until someone from TP-Link releases a new update for the adapter to make it run properly and stable without any packet loss or lag spikes, I will keep on using T3U)

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:TX20UH gets real hot, packet loss, and high ping spikes even with it's latest driver-Solution
2025-06-27 09:32:02 - last edited 2025-07-07 01:58:02

  @AyrtonPlays2 

Hi, thank you very much for your time and patience.

It is suggested to change the following adapter advanced settings:

  • Disable "SupportFT 11kv"
  • Turn off "Roaming Sensitivity."
  • Set "USB switch mode" to "USB 3.0"

 

If it didn't help, could you please help me check the following details:

Can I have the system information about your computer, such as How to check driver version of TP-Link adapters and system information of your computer

Please save some screenshots of the "packet loss, and high ping spikes" on the TX20UH.

 

You could send these details to support.forum@tp-link.com (please add the forum ID#822166)

Thanks a lot.

Best regards.

 

▶Check What's Currently Going on With Deco ▶Deco Wi-Fi Heatmap ready for Test! ▶Deco X50/X55_V1.3_1.3.1 Introduced Channel Selection, WiFi Access Control and WireGuard VPN ▶Deco BE65_V2_1.3.0 Added DoH & DoT, Speed Limit and Internet Backup Try to leave a Message if urgent help is required.
Recommended Solution
  0  
  0  
#2
Options
1 Reply
Re:TX20UH gets real hot, packet loss, and high ping spikes even with it's latest driver-Solution
2025-06-27 09:32:02 - last edited 2025-07-07 01:58:02

  @AyrtonPlays2 

Hi, thank you very much for your time and patience.

It is suggested to change the following adapter advanced settings:

  • Disable "SupportFT 11kv"
  • Turn off "Roaming Sensitivity."
  • Set "USB switch mode" to "USB 3.0"

 

If it didn't help, could you please help me check the following details:

Can I have the system information about your computer, such as How to check driver version of TP-Link adapters and system information of your computer

Please save some screenshots of the "packet loss, and high ping spikes" on the TX20UH.

 

You could send these details to support.forum@tp-link.com (please add the forum ID#822166)

Thanks a lot.

Best regards.

 

▶Check What's Currently Going on With Deco ▶Deco Wi-Fi Heatmap ready for Test! ▶Deco X50/X55_V1.3_1.3.1 Introduced Channel Selection, WiFi Access Control and WireGuard VPN ▶Deco BE65_V2_1.3.0 Added DoH & DoT, Speed Limit and Internet Backup Try to leave a Message if urgent help is required.
Recommended Solution
  0  
  0  
#2
Options

Information

Helpful: 0

Views: 763

Replies: 1

About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.