Home Network Community > Deco > I'm having trouble turning off the LEDs on my TP-Link Deco x10 slave station.
< Deco

I'm having trouble turning off the LEDs on my TP-Link Deco x10 slave station.

I'm having trouble turning off the LEDs on my TP-Link Deco x10 slave station.

I'm having trouble turning off the LEDs on my TP-Link Deco x10 slave station.
I'm having trouble turning off the LEDs on my TP-Link Deco x10 slave station.
2 weeks ago - last edited an hour ago
Model: Deco X10  
Hardware Version: V1
Firmware Version: 1.30 Build 20250725 Rel. 54254
I just bought, a TP-Link Deco x10 2-pack. The master station, is next to the computer, where the network router is, while the slave station, is in a completely different room. When I set it in Advanced Options -> LED Control -> Scheduled Shutdown, it only turns off the LEDs, on the master station. However, in the slave station, they stay on constantly, regardless, of which LED control option I choose. I sleep permanently in the room, where the slave station is. Where the master station is, there's a room that no one uses, so it doesn't matter, what state the LEDs, are in there. This bright blue, flashing light, is so bright, that I have to cover the LEDs (so that only the LEDs are covered, nothing else) with something opaque, so as not to disturb my sleep. In the Deco App, there's no distinction, as to which station the LEDs are turned off. Is it possible. to also turn off the LEDs, in the slave station?
 
 

 

 

 

  1      
 
  1      
 
#1
Options
2 Accepted Solutions
Re:I'm having trouble turning off the LEDs on my TP-Link Deco x10 slave station.-Solution
5 hours ago - last edited an hour ago

  @PieterBeeckman1 

Hi, welcome to the community.

Can I have the firmware version of your Deco X60?

Is your Deco offered by the ISP?

Wait for your reply.

Best regards.

 

▶Check What's Currently Going on With Deco ▶Deco X50_V1_1.8.0 Significantly Expanded the Client Connection Details and Added Channel Selection ▶Deco X50/X55_V1.3_1.3.1 Introduced Channel Selection, WiFi Access Control and WireGuard VPN ▶Deco BE65_V2_1.2.10 New Firmware with Enhanced Stability & Interference Resistance ▶Deco BE75 1.1.0 Added WireGuard VPN, Manual Channel Selection and More Try to leave a Message if urgent help is required.
Recommended Solution
  0  
  0  
#5
Options
Re:I'm having trouble turning off the LEDs on my TP-Link Deco x10 slave station.-Solution
an hour ago - last edited an hour ago

  @piotrkast  First of all, it's a Deco x10, not a Deco x60.

Yes, I have a dedicated, special router for wireless internet from the PLUS network in Poland.

I received this Deco x10 x2 set as a Christmas gift, not from an ISP.

Firmware version: 1.3.0 Build 20250725 Rel. 54254

Recommended Solution
  0  
  0  
#6
Options
5 Reply
Re:I'm having trouble turning off the LEDs on my TP-Link Deco x10 slave station.
2 weeks ago - last edited an hour ago

  @piotrkast 

Hi, did you set Deco X10 into "Wireless Router" or "Access Point "mode?

The LED control on the Deco X10_V1_1.3.0 is supposed to disable LEDs on all Deco units.

If possible, can you refer to this link to set the "satellite Deco X10" as the main Deco to see whether LED control can turn off LEDs on both Deco units:

How to replace the main Deco with another Deco

 

Thank you very much.

Best regards.

▶Check What's Currently Going on With Deco ▶Deco X50_V1_1.8.0 Significantly Expanded the Client Connection Details and Added Channel Selection ▶Deco X50/X55_V1.3_1.3.1 Introduced Channel Selection, WiFi Access Control and WireGuard VPN ▶Deco BE65_V2_1.2.10 New Firmware with Enhanced Stability & Interference Resistance ▶Deco BE75 1.1.0 Added WireGuard VPN, Manual Channel Selection and More Try to leave a Message if urgent help is required.
  0  
  0  
#2
Options
Re:I'm having trouble turning off the LEDs on my TP-Link Deco x10 slave station.
2 weeks ago - last edited an hour ago

  @David-TP I set Deco System as Access Point. I don't have menu "Replace Main Deco", so I switch Deco units, reset both devices (in a long reset), an again connect both units, to the internet. Problem with LED's is still the same. In main deco units (connected - and switched with the satelite unit - to the internet) , LEDs swith off, but in the satelite DECO - not. What else I can do, to switch LED's in satelite unit?

  0  
  0  
#3
Options
Re:I'm having trouble turning off the LEDs on my TP-Link Deco x10 slave station.
13 hours ago - last edited an hour ago

  @piotrkast I encounter the same issue (allthough model X60F), i'm albe to disable the led on the main station but not on the slave station. how can this be fixed @David-TP is there a software bug in the latest version?

  0  
  0  
#4
Options
Re:I'm having trouble turning off the LEDs on my TP-Link Deco x10 slave station.-Solution
5 hours ago - last edited an hour ago

  @PieterBeeckman1 

Hi, welcome to the community.

Can I have the firmware version of your Deco X60?

Is your Deco offered by the ISP?

Wait for your reply.

Best regards.

 

▶Check What's Currently Going on With Deco ▶Deco X50_V1_1.8.0 Significantly Expanded the Client Connection Details and Added Channel Selection ▶Deco X50/X55_V1.3_1.3.1 Introduced Channel Selection, WiFi Access Control and WireGuard VPN ▶Deco BE65_V2_1.2.10 New Firmware with Enhanced Stability & Interference Resistance ▶Deco BE75 1.1.0 Added WireGuard VPN, Manual Channel Selection and More Try to leave a Message if urgent help is required.
Recommended Solution
  0  
  0  
#5
Options
Re:I'm having trouble turning off the LEDs on my TP-Link Deco x10 slave station.-Solution
an hour ago - last edited an hour ago

  @piotrkast  First of all, it's a Deco x10, not a Deco x60.

Yes, I have a dedicated, special router for wireless internet from the PLUS network in Poland.

I received this Deco x10 x2 set as a Christmas gift, not from an ISP.

Firmware version: 1.3.0 Build 20250725 Rel. 54254

Recommended Solution
  0  
  0  
#6
Options

Information

Helpful: 1

Views: 86

Replies: 5

About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.