Archer C5400: Led Controller | ERROR | Config importing failed
Hardware Version :
Firmware Version :
ISP :
Firmware: 1.2.2 Build 20170912 rel.56240(5553)
Hardware: ArcherC5400 v2.0
In the system logs, it's flooded with the following error Config importing Failed. Can someone explain to me what this even means? What config is failing? -- I searched the googlags, however found nothing. What is odd, if i factory reset, I get this log from when I didn't even own the router ...
An extra bit of context: I'm having an issue where my 2.4GHz signal lands on channel 64 and my 5Ghz band-1 doesn't broadcast w/ a N/A port. And it displays the message of 5Ghz is not supported in your region (WA-USA ... which 5GHz is allowed). I'm wondering if the two are related -- the errors on import and the non-function tri-band...
Support told me to RMA this unit which feels wrong, I highly suspect this is a firmware issue ...
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Did the feature ever work for you? Are you on the latest firmware? Are you trying to import a config from a previous backup? If so do you know the FW version used on that back up? Can you provide screenshots of the error you are getting?
thank you
- Copy Link
- Report Inappropriate Content
I also have the same problem. and no, this did not work for me.
does anyone know hot to solve this? I used 1043nd fo 6 years and did not have nowhere near this number of problems with the router and I am using this for only 2 months!!!
help...
- Copy Link
- Report Inappropriate Content
Same here.
Hardware:
ArcherC5400 v2.0
Firmware:
1.2.2 Build 20170912 rel.56240(4A50)
Operation Mode
Access Point
I can't Time Settings from Internet. Always crrent date = 09/12/2017.
Is this relevant?
- Copy Link
- Report Inappropriate Content
Same problem here.
I had also troubles with WI-FI connections after a long time without reboot/shutdown. There must be a memory leak.
I would be glad to get a fix/new firmware for these problems.
- Copy Link
- Report Inappropriate Content
In my case, when I set the time manually, the error is no longer output.
- Copy Link
- Report Inappropriate Content
Thank you for this. I will forward this to our software team and have them investigate the potential issue.
Best Regards
- Copy Link
- Report Inappropriate Content
Hi everyone.
Our testing engneers have stated the issue typically happens if the wrong NTP servers are selected. Please ensure the correct one for your region has been mapped and see if the issue has been resolved. If not let me know!!!!
Best Regards
- Copy Link
- Report Inappropriate Content
Hi Carl.
>Our testing engneers have stated the issue typically happens if the wrong NTP servers are selected. Please ensure the correct one for your region has been mapped and see if the issue has been resolved. If not let me know!!!!
Thank you. but It's not so simple.
I am in Japan. I already tried the following NTP servers. but all failed.
ntp.jst.mfeed.ad.jp
ntp.nict.jp
ntp.ring.gr.jp
time.google.com
ats1.e-timing.ne.jp
Of course, I can connect to all NTP servers from my PC.
(PC is Connect to C5400)
Hardware:ArcherC5400 v2.0
Firmware:1.2.2 Build 20170912 rel.56240(4A50)
Operation Mode:Access Point
DHCP:Off
Fixed IP Address
I use two C5400, both have same problem.
I'm expecting new firmware.
- Copy Link
- Report Inappropriate Content
FWIW, I'm experiencing similar issues. Specifically:
- 2.4GHz band drops dead randomly daily
- same LED errors in the log as others have pointed out
- lost ability to control the LED setting after making the mistake of trying out the feature. Now my LEDs are PERMANENTLY off.
For such an expensive and better-than-average home router, I would have expected more active firmware releases. Come on TP-Link, latest one is dated 2017!
Firmware: 1.2.2 Build 20170912 rel.56240
Hardware: ArcherC5400 v2.0
- Copy Link
- Report Inappropriate Content
Information
Helpful: 1
Views: 15789
Replies: 21
Voters 0
No one has voted for it yet.