How to configure the gateway for an Archer C2300 in AP mode?
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.How to configure the gateway for an Archer C2300 in AP mode?
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Under the network settings, if I use a fixed IP, I can set the IP address and the MASK but not the Gateway. This means I can only connect to the AP management gui from within the same network.
I've upgraded to the latest firmware available but the option stills not there.
Is there any plan to include the gateway in the fixed IP settings section?
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
This is correct becasue as an AP the router is not longer a router and only accessible locally. The Gateway address is LAN address of the router it is connected to. If you want to be able to access it remotely you would need to have the C2300 setup as a router.
- Copy Link
- Report Inappropriate Content
But I don't want it as a router. I just want to be able to manage it from a different subnetwork as I usually do with other APs and network devices.
IMHO every network device should have the possibility to set a default gateway.
My LAN is separated from the WLAN for security reasons.
Is there any place where I could suggest this option to be included in future releases?
- Copy Link
- Report Inappropriate Content
I will send it up to our R and D team, that's not a problem but I would not bet on a solution. Since the routing comes from your router remote access to the device also would come from the router. If you simply try to gain remote access to the C2300 in AP mode then that access would need to be granted from the Router suppling the internet and IP to the AP. You would need to see if the router has settings that allows remote access to Local devices. If so it should just be a matter of setting that up on the router and knowing the IP and ports to access the AP.
- Copy Link
- Report Inappropriate Content
If the AP doesn't have a default gateway set I won't be able to even ping it from a different subnetwork to see if it is still alive. For any device in the network you have to set the IP, the Mask and a default gateway so it can go out of its network, that's why I found odd that this last setting is missing on the TP-Link AP.
- Copy Link
- Report Inappropriate Content
Hi Carl! I have a question about AP mode. I set up my second C2300 as an AP and works perfectly as an AP. Well almost! My question is that on my C2300 in router mode I see the AP fine but that in the router log the AP is just constantly pinging "TP-LINK.COM" Is there a reason it does this? I have taken both C2300 devices and switched their roles and no mater which plays the AP role the AP fills up the router syslog by constantly pinging "TP-LINK.COM" How can I stop this at the AP? What is the reason the C2300 in AP mode does this? Thanks! @GE0
- Copy Link
- Report Inappropriate Content
Hi! You could add a route to/from your other class c subnet to the routing table if your network is joined by a switch or router. You would not want to do that via the WAN port if on a public class a subnet for security reasons. Or use the router VPN feature. Just saying. @GE0
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@Carl Sorry for insisting, but it doesn't make sense to put an option to connect and check for the latest firmware upgrade if the AP doesn't know how to go out of the network because there is no option to set the default gateway. This happens in AP mode, I'm not using router mode, for that I have a dedicated router.
Every device you connect to a network must have a gateway to communicate with devices outside it's network. IMHO, this is a bug; I won't insist more on this topic, but it will make me look for other brands when I renew my network.
Thank you for your time.
- Copy Link
- Report Inappropriate Content
Its not a bug though. Its a factor of DHCP. When you put the C2300 in AP mode you are disabling all router functions including the DHCP server. This means that the Host router or a 3rd party device is providing the DHCP for the network. IPs would come from the device, usually the host router, that is handing out the DHCP addressing. This includes the Default Gateway. Accessing the AP locally is just a matter of connecting to the device via one of its Ethernet ports and using the management UI or via its Wireless and the management UI or Tether app. Remote management would require the C2300 to be in router mode or for you to know the IP assigned and having remote management enabled on the Host device. For the OTA updates you would need the device to be in router mode. It sounds though from your responses that you are looking for a more enterprise level AP where you are able to access, manage and update remotely. If that is correct you are using the wrong product. The C2300 is a home product and you would want something in our Business product line. Look at the EAP225 or anything in our Omada product line. These devices would meet those requirements more effectively.
- Copy Link
- Report Inappropriate Content
I have my network routing working fine and all the other networking devices are able to go out of their subnetwork because I can configure their default gateway, which tell them how to go out. The problem here is that when you put this archer C2300 in AP mode, there is no way to configure the gateway IP, only it's IP address and network mask; since I can't configure it, there is no way this device (the management interface) is able to communicate with the other subnetworks nor the internet.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 2178
Replies: 12
Voters 0
No one has voted for it yet.