Home Network Community > All Threads > 100Mb between 2.5Gb port on Archer AXE300 and TL-SG108-M2
< All Threads

100Mb between 2.5Gb port on Archer AXE300 and TL-SG108-M2

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

100Mb between 2.5Gb port on Archer AXE300 and TL-SG108-M2

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
100Mb between 2.5Gb port on Archer AXE300 and TL-SG108-M2
100Mb between 2.5Gb port on Archer AXE300 and TL-SG108-M2
2024-03-12 01:40:32
Model: Archer AXE300  
Hardware Version: V1
Firmware Version: 1.0.9 Build 20230525 rel.2592(5553)

I have an Archer AXE300.  We use WiFi for all devices.  I just bought a TL-SG108-M2 (8x 2.5Gb switch).  I connected it to the 2.5Gb port on the router with a new CAT6 cable.  The 3 PCs that are being wired support 2.5Gb ethernet.  Speed tests from all PCs show less than 100Mb.  PC directly connected to 2.5Gb port shows 100Mb.  In the router configuration, network map, Archer AXE 300, the 2.5 port shows 100Mb when connected to a PC directly or the switch.  Is there a setting I am missing somewhere?

  0      
 
  0      
 
#1
Options
3 Reply
Re:100Mb between 2.5Gb port on Archer AXE300 and TL-SG108-M2
2024-03-12 10:22:13 - last edited 2024-03-12 10:23:33

  @NeghVar1 

 

You can try setting the Interne t negotiation speed to :

 

e01eb89270e04efebce4fe3b75b9bea2

 

if it is on Auto Negotiation.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#2
Options
Re:100Mb between 2.5Gb port on Archer AXE300 and TL-SG108-M2
2024-03-13 03:14:18

  @terziyski It should be set on auto-negotiation. Both sides of the cable should have the same setting if you try changing it.

I would try a different cable first, and check if it plugs in properly. Some notepad ports are rather deep and connector cover pushes it out. Maybe some wire is not connected and then it negotiates to 100 mbps which uses only 2 twisted pairs out of 4.

Marketplaces are full of cheap fake cables. You can try your existing WAN cable you know is working, just to check ethernet speed negotiation.

  0  
  0  
#3
Options
Re:100Mb between 2.5Gb port on Archer AXE300 and TL-SG108-M2
2024-03-13 08:45:27

  @Rch11 

 

I would agree with that. My suggestions was to check if there would be any change in the negotiated speed (100mbps).

Ideally this setting should be on auto-negotiation. Sometimes though it should be set manually to get things running properly.

This type of issues are most often caused by a bad cabling and in rare cases by faulty ethernet ports or even a FW glitch.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#4
Options

Information

Helpful: 0

Views: 363

Replies: 3

Related Articles
Lan/ ethernet issues AXE16000 Archer axe300
1123 0
Archer AXE300 Firmware Alternatives
65 0
500Mb/s with 100Mb/s port
769 0
No Virtual Server Option on AXE300/16000
626 0
Archer AXE300 (AXE16000) - Very poor wireless performance.
2429 1
Can't see my Wifi 6 SSID with devices that support Wifi 6 with my Archer AXE300
1692 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.