FW 1.3.0 Release for M9 Plus: Any issues?
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Anyone run into any show stoppers with FW 1.3.0? I'm so wanting to hit the update button.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi all,
As you know, the latest firmware 1.3.0 for Deco M9 plus V1 has been released, which has added some new features.
For more information, you can view the released note on the offical website.
https://www.tp-link.com/support/download/deco-m9-plus/v1/#Firmware
@NoMadMan You can update it or wait for a while until get much enough feedback on the latest firmware.
@Superior3000 To access the web UI, please ensure that you have connected to the Deco network, clear the browser cache and change another web browser or device to give it a go; Meanwhile, you can open a New incognito window to access it.
May it help and have a nice day.
- Copy Link
- Report Inappropriate Content
Updated yesterday, for now don't have any problems. Can saturate my internet connection from wired connected computer and have same bandwidth from WiFi devices as earlier. Web interface is working but functions are sooo limited.
- Copy Link
- Report Inappropriate Content
@NoMadMan update on a remote site done ok, nice to see how the 4 units are connected. The mesh is extended trough two Tp-link antennas & now we discovered that the unit is connected via wifi not ethernet, must check the antennas.
- Copy Link
- Report Inappropriate Content
I have no issues so far.
But I can't access the web interface. Not via 192.168.68.1 and not via http://tplinkdeco.net/.
I have 4 units of the M9 Plus (fw 1.3.0) and one unit M5 (1.3.1). I am on the wifi of the Deco network. Does anyone have suggestions?
- Copy Link
- Report Inappropriate Content
Hi all,
As you know, the latest firmware 1.3.0 for Deco M9 plus V1 has been released, which has added some new features.
For more information, you can view the released note on the offical website.
https://www.tp-link.com/support/download/deco-m9-plus/v1/#Firmware
@NoMadMan You can update it or wait for a while until get much enough feedback on the latest firmware.
@Superior3000 To access the web UI, please ensure that you have connected to the Deco network, clear the browser cache and change another web browser or device to give it a go; Meanwhile, you can open a New incognito window to access it.
May it help and have a nice day.
- Copy Link
- Report Inappropriate Content
Hi Kevin,
Still not working. I have tried to access the web UI via wifi, according instructions on https://www.tp-link.com/en/support/faq/2641/.
I have:
- cleared browser history
- tried incogniito
- tried http://tplinkdeco.net/ and http://192.168.68.1/
- tried Chrome, Edge and Internet Explorer
- All Deco units on latest firmware
Is it because of my mix of M9 and M5 units?
- Copy Link
- Report Inappropriate Content
@Superior3000 In my case the website showed an empty page after logging in in Chrome. I tried it in Edge and there it worked. Not clear why and how. I have also the V1.
- Copy Link
- Report Inappropriate Content
Does anyone know if the bug where the device reverts to the default IP range on every reboot (172.16.0.xxx) was fixed? gotta love patch notes that just says "fixed some bugs" , id rather they say nothing than this BS comment
- Copy Link
- Report Inappropriate Content
Hello, this issue is caused by the IP address conflict detection mechanism in some cases. It should be fixed already.
Good day.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 1979
Replies: 8
Voters 0
No one has voted for it yet.