Can it work "EAP225-Outdoor" to "LAN"? (not mesh function)
Hello?
I have some question.
I just want to receive any WI-FI signal using EAP225-Outdoor and change to LAN (WLAN -> LAN)
any WI-FI signal (available internet) ((( EAP225-Outdoor -> LAN
Can EAP225-Outdoor work like this?
Many Thanks
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi @Sugar_Rush,
Yes, absolutely. You can connect the EAP-225-Outdoor directly to your Ethernet network. In fact this is the preferred solution for maximum performance. Note that this AP, like the rest of the 225/245 line are PoE. So you will either need to use the included PoE injector or use a compatible PoE ethernet switch.
Do you have other TP-link equipment? e.g. 225V3 or 245V3? OC-200 or SDN/Omada server software?
-Jonathan
- Copy Link
- Report Inappropriate Content
I have CPE520 products.
(Lower than 25dbm. Our country didn't allow over 25dbm. CPE220 support 2.4Ghz but that is over 25dbm)
CPE520 support only 5Ghz.
I use CPE520 Client mode like this.
Any Wireless Internet))) (((CPE520(client mode) -> PoE -> router -> computer
EAP225-Outdoor support 2.4Ghz. So I want to use EAP225-Outdoor like this
Any Wireless Internet))) (((EAP225 -> PoE -> router -> computer
So is that possible to set a system like this?
Give me some hint!
Many Thanks^^
- Copy Link
- Report Inappropriate Content
Dear @Sugar_Rush,
EAP225-Outdoor support 2.4Ghz. So I want to use EAP225-Outdoor like this
Any Wireless Internet))) (((EAP225 -> PoE -> router -> computer
So is that possible to set a system like this?
I'm afraid that EAP225-Outdoor cannot work like that. EAP225-Outdoor is just an access point, which is required to be hardwired to the Internet via cable.
I have CPE520 products. (Lower than 25dbm. Our country didn't allow over 25dbm. CPE220 support 2.4Ghz but that is over 25dbm)
CPE520 support only 5Ghz. I use CPE520 Client mode like this.
Any Wireless Internet))) (((CPE520(client mode) -> PoE -> router -> computer
For your concern, may I ask why you need a 2.4GHz device? Is the Wireless Internet providing 2.4GHz or 5GHz, or both? Do you have any issues with the 5GHz CPE520?
Please kindly note that the CPE520 in Client mode doesn't broadcast 5GHz WiFi, but only pick up the WiFi signal from the Wireless Internet and then feed the Internet to the behind router (or AP) via Ethernet cable. If your demand is to receive 2.4GHz WiFi on the computer, you could add the EAP225-Outdoor to make it, so the setup is like this:
Wireless Internet )))5GHz((( CPE520(client mode) ----- router ----- EAP225-Outdoor )))2.4G&5G((( computer or other wireless clients
Note: in the setup above, the router can be removed according to your actual requirements as it's not a must.
- Copy Link
- Report Inappropriate Content
@JSchnee21 hi following this thread.
I have a few eap225s all connected via a poe switch with Omada controller.
the last eap to be connected was an outdoor type, that is for some reason only connecting wirelessly, even though it's plugged directly into the poe switch.
how do I go about changing this to LAN? Normal reset not making any difference.
TIA
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 2330
Replies: 4
Voters 0
No one has voted for it yet.