Business Community > Wireless > Access Point not detected
< Wireless

Access Point not detected

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Access Point not detected

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Access Point not detected
Access Point not detected
2023-12-14 13:53:19 - last edited 2023-12-16 18:03:20
Tags: #Installation #Network Connectivity
Model: EAP610-Outdoor  
Hardware Version: V1
Firmware Version: 1.2.3 Build 20230922 Rel. 67667

Hi,

 

I want to connect my access points via a wire to ensure a stable connection.

 

Thus far, I have come this far:

 

gateway - switch - EAP615

Everything worked

 

Now I have connected the EAP615 to an EAP 610 outdoor but the EAP610 is not detected.

- I have verified the quality of the cable I used

- I used the ETH1 port on the EAP615 and checked the box in the configuration of the controller

- the EAP610 is connected to the EAP615 through the LAN port of its POE injector

 

What am I missing? Earlier it was connected wirelessly, and that went well.

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Access Point not detected-Solution
2023-12-16 13:39:57 - last edited 2023-12-16 13:48:12

  @janaca 

Do NOT check the controller box, unless you have pre-configured the 610 with a different management VLAN!  This forces the port to use tagged traffic.

The ports will work just fine if they are unticked on the default VLAN.

 

<< Boycotting this site and these products until CANADIAN firmwares get some love >>
Recommended Solution
  0  
  0  
#7
Options
7 Reply
Re:Access Point not detected
2023-12-14 14:04:54

  @janaca 

 

Is the POE on that 615 port enabled?

 

 

I can not teach anyone anything - I can only make them think - Socrates
  0  
  0  
#2
Options
Re:Access Point not detected
2023-12-14 14:07:15

  @KimcheeGUN Yes, it is. But I do not use it. I picked the ETH1 port.

  0  
  0  
#3
Options
Re:Access Point not detected
2023-12-14 14:21:58

  @janaca 

 

Make sure you are running the latest firmware for the EAP615-wall.  Keep in mind that the default VLAN for management is VLAN1-untagged, so you will need the switch and AP ports set appropriately.

<< Boycotting this site and these products until CANADIAN firmwares get some love >>
  0  
  0  
#4
Options
Re:Access Point not detected
2023-12-14 14:28:33

  @d0ugmac1 

 

The switch is unmanaged, so I suppose I cannot set it.

 

This is how I have set the EAP615, is it correct?

  0  
  0  
#5
Options
Re:Access Point not detected
2023-12-16 13:25:02

I have removed the EAP615 and put another switch to connect the controller to the EAP60. Then the EAP610 was recognized immediately!

 

So the problem must lie in the configuration of the ethernet ports on the EAP615. I have another EAP615 where the LAN ethernet connections don't work either. Only the POEport works...

 

The controller is still in the default mode (vlan1), I have not changed anything.

 

 

 

  0  
  0  
#6
Options
Re:Access Point not detected-Solution
2023-12-16 13:39:57 - last edited 2023-12-16 13:48:12

  @janaca 

Do NOT check the controller box, unless you have pre-configured the 610 with a different management VLAN!  This forces the port to use tagged traffic.

The ports will work just fine if they are unticked on the default VLAN.

 

<< Boycotting this site and these products until CANADIAN firmwares get some love >>
Recommended Solution
  0  
  0  
#7
Options
Re:Access Point not detected
2023-12-16 13:48:05

  @d0ugmac1 THANK YOU! Now it's all there :-)

 

I must say, it is confusing... If I don't check the POE box, the port won't work, so I thought I also had to check the LAN boxes.

  0  
  0  
#8
Options

Information

Helpful: 0

Views: 987

Replies: 7

Tags

Installation Network Connectivity
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.