Issues with tcp connections between VLANs on the same AP
I'm having issues streaming some networked (WiFi) cameras across VLANs, but only when the client device is on the same AP as the camera. When my client device is connected to a different AP everything streams perfectly. But when they share an AP the stream dies before it can even start. I have 3 total APs, all EAP650. Two are directly connected to my switch, one is using wireless mesh. If the cameras are in the same VLAN as the client device it works perfectly. if the cameras are on a different VLAN AND a different AP it works perfectly. If the cameras are on a different VLAN but the SAME AP, it does not work.
I cannot figure out why this would be.
Update: This is caused because TCP connections will drop unexepectedly when connecting to the same AP from where they initiated, on a different ssid/vlan
I isolated it to the EAP 650 access points I was using. I replaced them with some netgear access points set up with the same SSIDs and VLANs and it works 100% correctly.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Dear @jrypacek,
jrypacek wrote
I've bought EAP653 and probably got the issue on firmware 1.0.1 Build 20220524 Rel. 60447.
I'm using Omada controller and have opened 2 issues for EAP610 with your support team, so they already have my configuration file.
I tried ping - OK, SSH - OK, iperf3 UDP - OK, iperf3 TCP - FAIL.
I had notebook and mobile connected to the same AP and tried two scenarios. Behavior was the same on both.
1) notebook on 5GHz, mobile on 2.4 GHz IoT SSID - guest newtork enabled + ACL
2) notebook on 2.4GHz, mobile on 2.4 GHz IoT SSID - guest newtork disabled, no ACL
Thank you so much for your valuable feedback!
The support engineer has reproduced the problem and reported it to the R&D team for further analysis. Any update, I'll let you know.
- Copy Link
- Report Inappropriate Content
Hello @Fae
I believe I could be hitting the same or a similar issue that's been described on this thread.
You can check my topic post regarding the situation.
Any news regarding a fix? EAP650(EU) V1
- Copy Link
- Report Inappropriate Content
Dear @s0x,
s0x wrote
I believe I could be hitting the same or a similar issue that's been described on this thread.
You can check my topic post regarding the situation.
Any news regarding a fix? EAP650(EU) V1
Thanks for your valuable feedback. Our R&D team has located the cause of the issue, they are currently discussing the suitable solution. I'll update this thread once there is a fix.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Dear @Spryde,
Spryde wrote
Any news or timeline concerning the fix?
Sorry that I haven't been informed of an update on the issue yet. But the R&D team confirmed that they would provide a Beta firmware to fix the issue, I'll let you know once the beta firmware is available. Thank you for your great patience!
- Copy Link
- Report Inappropriate Content
Dear @treas, @jrypacek, @d0ugmac1, @s0x, @Endpoint7024, @Spryde, @shberge,
Thank you all for your great patience while we work through this issue!
Regarding the issue with TCP connections (such as Remote Desktop) between VLANs on the same EAP650/EAP670/EAP653 v1, the R&D team has made a Beta firmware to fix it, which has also added the PPSK support, please follow this solution post for downloading.
Thank you for your attention! Look forward to hearing from you on our community soon!
- Copy Link
- Report Inappropriate Content
Why not bringing it as a final firmware?
For now every user has to use your beta firmware (and your beta tracking/analysing policies) to have a working product?
Or maybe you can make a firmware which is beatween final and beta - a release candidate without beta policies.
I don't want to be a beta tester.
- Copy Link
- Report Inappropriate Content
From what I've seen, TPlink has a fairly robust software development methodology and process, I might even wager they have adopted an Agile approach :) This forum forms a big part of getting feedback from the field which they then incorporate and priortize into upcoming releases. Their beta program gets fixes out in the field as quickly as possible, but not without some interim testing...ie they didn't just up some code and punt it to you. Instead, their 'beta' release are more like interim versions between the major official releases. I've been running beta code on my 2008 for months now...because it fixes a niggling problem I had with it...and I didn't want to wait more months for the next major release.
I for one would rather have access to beta code than not.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
I just loaded this beta firmware on my EAP670.
I am now finding that my 5GHz wifi is not broadcasting when I had it set on channel 100.
5Ghz channel 100 working back on firmware 1.0.2.
I have it set to 160mhz bandwidth.
On a positive note, it seems the issue of the lower channels 36-64 are now correctly set to be max power output of 30dbm, not 23bdm as in previous firmware.
It also looks like UAPSD is not working on this firmware. I am no longer seeing the green lightblub next to any of the devices in the omada client list.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 1
Views: 7699
Replies: 52