Omada Hardware Controller showing WIFI clients on LAN Wired Network
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.Omada Hardware Controller showing WIFI clients on LAN Wired Network
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hi,
I have get issue in my Omada VPN ER605 and Hardware Controller OC300 1.0 (Firmware Version 1.14.7 Build 20221206 Rel.60706)
the problem we are facing my clients that are connected to WiFi EAP. But the controller software says they are connected to my Lan (TL-R605)
and the EAP which we are using all connected through the CAT 6 Cable due to this problem Im facing a lot problem in Voucher Portal even for
clients
the measure problem is the WIFI is connected through the client mobile but internet is not working even the mobile is showing good WiFi Signal but
when you just check the ip address on the Omada Portal its showing 2 clients on one ip so I don't why the Omada Controller issue the one ip address
on two Clients 
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hello again!
I just re-read the thread, and realized I'd made a typo where I'd suggested splitting the networks. What I'd meant was the following:
Devices: 134.1.1.0/24
Clients: 134.1.4.0/18 (not 16) and I would suggest even making it 134.1.4.0/22 which still gives you a thousand IP's to hand out to your 750 users.
Next up, I have been working with support for months on what I perceive to be a memory leak issue in the software architecture used by the ER routers. It is worst on the ER605v1 as it has by far the least amount of memory and so things tend to happen fastest and first on that model. Essentially I have been seeing a linear increaes in real memory consumption over time, which eventually gets to the point where memory starvation occurs...when this happens, process crash...typically it's the Omada application which causes disconnects, but I believe I have seen DHCP die first as well. So I"m recommending you reduce the pool of IP's for clients to reduce the amount of resources required on the router and controller to track them all. I'm also going to suggest you perform a weekly reboot (the controller has the ability to configure the Reboot Schedule for devices, and reset just the ER7206 at 4am Saturday or whatever). This and updating to the latest firmware should help eliminate the spinning 'Waiting for IP' stuff on clients.
Now to your new question, you wanted two policies...did you just mean you want to the two subnets to behave as expected, or do you have different gateways? I need a little more clarity around exactly what you are asking for. Also, a screen grab of your topology with Labels on would help me understand the hardware architecture, and a screen grab of all subnet definitions in the Wired Networks->LAN would be good too.
- Copy Link
- Report Inappropriate Content
Hello @d0ugmac1
I hope you are fine,
our team facing some problems with the Omada OC300 Hardware controller, when we unauthorize any client from the captive portal the error occurs Unauth failed, try again when the network recovers what does it mean? the internet is already connected from the VPN Router.
OC300 Hardware Controller
Firmware Version: 1.19.3 Build 20230906 Rel.38429
Controller Version: 5.12.9
Model: OC300 1.0
- Copy Link
- Report Inappropriate Content
@AnnusKhan Hi, we might need @Clive_A or @Hank21 to wade in here, but the error sounds like somebody isn't connected to somebody else, whether that is your device is on a VLAN that doesn't have access to some component of the captive portal, or the portal itself is not getting a response from say a device gateway. I don't use CP's so I"m a bit in the dark here.
- Copy Link
- Report Inappropriate Content
Hi @AnnusKhan
Thanks for posting in our business forum.
Is your original issue resolved or not? If no, I'll continue the original issue with you.
The new issue you said "unauth", is a controller issue which I don't know a lot about. I suggest you start a new thread in the Controller section.
- Copy Link
- Report Inappropriate Content
Thank you Clive for your reply
the problem we are facing has been fixed by my team, after changing of VPN router and we do not get any "unauth" error in Captive Portal right now
but after this, we just getting another problem which I highlighted before to @d0ugmac1 that some wireless Client is showing on the wired Network
this is happening after we just replaced the VPN router, we don't have any problem like this before , so look into this matter and let us know about
the solution because due to this situation we have getting internet problems to clients.
VPN_R: ER8411 v1.0
Firmware Version:1.1.0 Build 20230705 Rel.64091
Omada_CN:OC300 1.0
Firmware Version:1.19.3 Build 20230906 Rel.38429
we have a total 8 sites, and only in 2 sites we are getting this problem even though the configurations of all site is the same
All sites we are having the same VPN_Routes and Omada_Controllers
- Copy Link
- Report Inappropriate Content
Hi @AnnusKhan
Thanks for posting in our business forum.
AnnusKhan wrote
Thank you Clive for your reply
the problem we are facing has been fixed by my team, after changing of VPN router and we do not get any "unauth" error in Captive Portal right now
but after this, we just getting another problem which I highlighted before to @d0ugmac1 that some wireless Client is showing on the wired Network
this is happening after we just replaced the VPN router, we don't have any problem like this before , so look into this matter and let us know about
the solution because due to this situation we have getting internet problems to clients.
VPN_R: ER8411 v1.0
Firmware Version:1.1.0 Build 20230705 Rel.64091
Omada_CN:OC300 1.0
Firmware Version:1.19.3 Build 20230906 Rel.38429
we have a total 8 sites, and only in 2 sites we are getting this problem even though the configurations of all site is the same
All sites we are having the same VPN_Routes and Omada_Controllers
Do you apply the Omada switches and EAP in your setup? I mean all of the devices are Omada?
Picture shows that they are wired to the port, and do you have another switch or AP cascade on the Omada switch? If yes, that might display incorrect devices due to other brands' networking devices.
- Copy Link
- Report Inappropriate Content
Thank you for the solution, the problem has been fixed by the team
Yes @Clive_A there is some unknown access point connected throught the Omada swtich
so when the client is connected through Unknown AP the omada_CN showing clients on the wired network
now the problem is fixed
Thank you so much for your support.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 2256
Replies: 17
Voters 0
No one has voted for it yet.