Home

Forums

Stories

Knowledge Base

Business Community > All Threads > Need help on Allowing only certain ports on Omada

< All Threads

Need help on Allowing only certain ports on Omada

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Need help on Allowing only certain ports on Omada

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

jwaltrip

2023-10-11 19:19:07 - last edited 2023-10-13 01:22:23

Posts: 69

Helpful: 8

Solutions: 3

Stories: 0

Registered: 2021-10-15

Need help on Allowing only certain ports on Omada

2023-10-11 19:19:07 - last edited 2023-10-13 01:22:23

Tags: #VLAN & Multi-Networks #Switch ACL

Model: ER605 (TL-R605)

Hardware Version: V1

Firmware Version: 1.3.0

Omada:

ER605 v1

EAP610

3 x SG2008P

Multiple VLANs, inclusing IOT VLAN

Questions are arount IOT VLAN

I already iknow how to block access to entire VLAN (I block MGMT and WIFI from IOT)

Here iwhat I want to do:

IOT ---> Other VLANS = Only allow list of ports to other VLANS

Other VLANS ---> IOT = Only allow list of ports to IOT VLAN

I assume it is some combination of Deny and Allow rules...

Does anyone know how to do this?

1 Accepted Solution

jwaltrip

LV2

2023-10-12 03:37:01 - last edited 2023-10-13 01:22:23

Posts: 69

Helpful: 8

Solutions: 3

Stories: 0

Registered: 2021-10-15

Re:Need help on Allowing only certain ports on Omada-Solution

2023-10-12 03:37:01 - last edited 2023-10-13 01:22:23

I figured it out....

1. Created bidirectional rule that listed ports that I wanted open as source. Set it to all networks are destination.

2. Created bidirectional rule after that, that blocks all ports.

this way, if I am accessing something on one of the listed ports, it connects. If I am trying to access a port not listed, it blocks it.

Recommended Solution

2 Reply

Md-Ripon3

LV2

2023-10-12 03:26:55

Posts: 30

Helpful: 4

Solutions: 7

Stories: 0

Registered: 2023-09-25

Re:Need help on Allowing only certain ports on Omada

2023-10-12 03:26:55

@jwaltrip

I hope this link helps you：

How to configure Multi-Networks & Multi-SSIDs on Omada SDN Controller | TP-Link

jwaltrip

LV2

2023-10-12 03:37:01 - last edited 2023-10-13 01:22:23

Posts: 69

Helpful: 8

Solutions: 3

Stories: 0

Registered: 2021-10-15

Re:Need help on Allowing only certain ports on Omada-Solution

2023-10-12 03:37:01 - last edited 2023-10-13 01:22:23

I figured it out....

1. Created bidirectional rule that listed ports that I wanted open as source. Set it to all networks are destination.

2. Created bidirectional rule after that, that blocks all ports.

this way, if I am accessing something on one of the listed ports, it connects. If I am trying to access a port not listed, it blocks it.

Information

Helpful: 0

Replies: 2

Need help on Allowing only certain ports on Omada

Need help on Allowing only certain ports on Omada

Information

Voters 0

Tags