Deco Forums - Home Network Community

"IoT Network" option not available on Deco PX50 App

Hello everyone, this is my first post here, Deco App (Android) version: 3.5.15 Deco PX50 hardware version: EU/1.0 Deco PX50 firmware version: v1.03 Build 20230420 Rel. 77020 Just purchased a Deco PX50

Firmware UpdateIoT Network

By eLeMenCy · Latest post 2023-09-05 13:41:34 by eLeMenCy

1Helpful

402Views

2Replies

dns hijack found. what to do?

By sakariteuvo · Latest post 2023-09-05 12:03:50 by sakariteuvo

0Helpful

240Views

3Replies

DDNS tplinkdns is not working

Dear Support, A few days ago i recognized that i am not able to acces my home servers that are using port forwarding from the outside. Turned out my tplinkdns.com is faulty. When i change to NOIP or d

DDNSPort Forwarding

By A0vy · Latest post 2023-09-05 11:21:00 by A0vy

1Helpful

353Views

5Replies

Deco x73-DSL Connects to Internet for 1 min then disconnects

My X73-DSL modem suddenly stopped connecting to the internet. Now if I pull out the power and plug it in again it will connect to the internet for about a minute and then disconnect. When I check the

VLAN/IPTVDeco Ethernet Backhaul

By DBL2 · Latest post 2023-09-05 10:51:42 by DBL2

1Helpful

268Views

2Replies

Deco network split in two, twice

Hi TP-Link world, My new Deco mesh has disappointed me twice now. Firstly, during a power outage test, then during a network outage test. In both cases the network was split between ethernet connected

Deco Ethernet Backhaul

By blindman2k · Latest post 2023-09-05 03:36:07 by blindman2k

3Helpful

343Views

4Replies

Deco E4

Hello how are you guys ? I have deco E4 and my connection is 300 mb Can I buy deco s4 and make it the main deco and put 3 decos E4 and gets more than 100 mb ? Sorry of my bad English Thank you

By NasseAlmojel · Latest post 2023-09-04 16:32:04 by NasseAlmojel

9Helpful

461Views

8Replies

Deco E4 Access Point mode

Hi everyone. I have a doubt about the functioning of the Deco mesh system. I have two Deco E4, the main one connected via ethernet to a switch. The second connected to the main with wifi connection (w

By cl-7k-01 · Latest post 2023-09-04 15:15:31 by cl-7k-01

2Helpful

366Views

8Replies

Deco X55 and VR600 v3

Hi, I was looking at setting up the Deco X55 Mesh I'm trying to avoid NAT on NAT on NAT as I have Cable broadband in router mode, is this the best way to go ?? I do have a VR600 v3 with which I use th

RoamingDeco Ethernet BackhaulAccess Point ModeVPN

By Garry_C999 · Latest post 2023-09-04 13:58:42 by Alexandre.

1Helpful

226Views

1Replies

Deco P9 connected to 300Mbps broadband never goes above 160Mbps over the powerline

I have a network of 3 Deco P9 connected to the same powerline wire. The main unit is connected to 300Mbps broadband (measured at the router https://fast.com ) but the other two P9 never show more than

By TWhite · Latest post 2023-09-04 13:40:11 by Alexandre.

1Helpful

145Views

1Replies

Add VPN

Hi there, I just brought a Surfshark VPN account. Unfortunately I can't setup the account in my TP-link Deco X60 router via the deco app. Please help me, thanks!

VPN

By hoylg · Latest post 2023-09-04 11:14:17 by DeaNHtiD99

3Helpful

732Views

8Replies