Home

Forums

Stories

Knowledge Base

Home Network Community > 5G/4G Wi-Fi Routers/MiFi > unable to connect in wireless router mode

< 5G/4G Wi-Fi Routers/MiFi

unable to connect in wireless router mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

unable to connect in wireless router mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

ithomas

2019-09-23 11:32:54 - last edited 2019-09-24 08:40:16

Posts: 3

Helpful: 0

Solutions: 1

Stories: 0

Registered: 2019-09-23

unable to connect in wireless router mode

2019-09-23 11:32:54 - last edited 2019-09-24 08:40:16

Model: Archer MR600

Hardware Version: V1

Firmware Version: 1.1.0.0.9.1 v0001.0 build 190412 Rel.66770n

I've configured the wireless router mode to use my ISP (BT) but unable to connect

These are the steps I've taken

BT Modem connected to phone line and connected LAN cable from this to the tplink WAN port

Configured router to Wireless router mode on the MR600 and started the quick setup

Enabled vlan with vlan id of 101

Username as - bthomehub@btbroadband.com

Password - bt

At this point I get the error "internet not connected. Please configure your parameters"

I have tested with an old TD-W9980 in wireless mode using the same ISP details and this connects ok with no issue.

Could someone please advise if there is something else I need to check or if this is a known issue?

1 Accepted Solution

ithomas

LV1

2019-09-24 08:39:39 - last edited 2019-09-24 08:40:16

Posts: 3

Helpful: 0

Solutions: 1

Stories: 0

Registered: 2019-09-23

Re:unable to connect in wireless router mode-Solution

2019-09-24 08:39:39 - last edited 2019-09-24 08:40:16

Removing the VLAN ticket seems to have fixed the issue, the MR600 is connecting through VDSL ok now. Thanks for your help

Recommended Solution

3 Reply

Kevin_Z

2019-09-24 02:50:38 - last edited 2019-09-24 02:50:55

Posts: 21587

Helpful: 5041

Solutions: 2543

Stories: 21

Registered: 2018-12-24

Re:unable to connect in wireless router mode

2019-09-24 02:50:38 - last edited 2019-09-24 02:50:55

@ithomas

As far as I know, the TD-W9980 does not support VLAN ID in wireless router mode, so may I know have you ever enabled VLAN ID on it when you set it up as the regular wifi router?

In the meantime, it is suggested to disable VLAN ID on the Archer MR600, put in the username and password only after you changed the operation mode to give it a go.

Still the same, please show us a screenshot of the advanced-status page.

May it help. Good day.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.

ithomas

LV1

2019-09-24 08:39:39 - last edited 2019-09-24 08:40:16

Posts: 3

Helpful: 0

Solutions: 1

Stories: 0

Registered: 2019-09-23

Re:unable to connect in wireless router mode-Solution

2019-09-24 08:39:39 - last edited 2019-09-24 08:40:16

Removing the VLAN ticket seems to have fixed the issue, the MR600 is connecting through VDSL ok now. Thanks for your help

unable to connect in wireless router mode

unable to connect in wireless router mode

Information

Voters 0

Tags