Deco X20 network repeatedly failing

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Deco X20 network repeatedly failing

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Deco X20 network repeatedly failing
Deco X20 network repeatedly failing
2020-04-01 00:58:50
Model: Deco  
Hardware Version: V1
Firmware Version: 1.2.2 Build 20200219 Rel. 41630

Home network has two Deco X20's with ethernet backhaul.  Modem and master unit are in a hallway closet, ethernet over to a TP Link SG105E in the living room and the slave unit is connected to that switch along with some other devices like a VOIP phone and an XBox.  

 

The Decos are failing at least once every day and generally in a little "storm" of repeated failures for anything from 10 minutes to an hour.  Sometimes it is just the slave that fails, sometimes it is the master.  By "failing" I mean the LED changes to red, all the devices connected to them lose their connection.  I have tried disconnecting the slave from the switch to use wireless backhaul, turning off mesh networking for some of the devices that don't move from one location and assigning static IP addresses for some devices (sometimes we were getting warning messages on some of the devices that there was another machine with the same IP address, or security softwark suspected ARP cache poisoning attacks), but the problems have persisted.

 

 

 

  0      
  0      
#1
Options
3 Reply
Re:Deco X20 network repeatedly failing
2020-04-01 01:39:05

@PCB 

 

Thanks for the information. We will do some troubleshooting to locate this issue and try to figure it out. 

 

1. When the led turns red, is there any error message on the Deco app? 

 

2. Try to switch the slave Deco to the main Deco and take some time to test the stability. 

https://www.tp-link.com/support/faq/2400/

 

3. When master Deco stops working, please connect your computer to the modem directly and verify whether you can access internet. 

 

4. Besides, how do you recover the network once it crashes? 

 

Good day. 

 

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re:Deco X20 network repeatedly failing
2020-04-01 02:44:25

Thanks @Kevin_Z 

 

  1. I haven't seen any error message on the Deco app other than to say it isn't connected to wireless.  I have looked at the system logs through the Web interface (can supply copies if that helps) but although there was a lot of messages listed under the ERROR category, I didn't see something there I could clearly act on.
  2. Sure, I will try that later tonight.
  3. Sure
  4. There isn't anything that I've done that has categorically helped reconnect the network, ultimately the fix seems to be just waiting until the units sort themselves out and hope it doesn't happen again.
  0  
  0  
#3
Options
Re:Deco X20 network repeatedly failing
2020-05-07 01:38:12

@PCB 

 

I am also having the same issue....my X20 keeps rebooting... sometimes it takes turn rebooting (LED from yellow->red->green), it happens every day or every few hours or so..I thought is the latest firmware or the unit is faulty, so I got TP-Link to replace the unit.  I just received the new unit yesterday, didn't upgrade the firmware, but I still have the same problem...

  0  
  0  
#4
Options