Archer MR600(EU) V1 - BETA Firmware - Allowing selection of 4G+bands for Archer MR600 manually
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hi all,
Following the long thread on the same subject discssing the BETA FW, as I said I would, TPLink have given me permission to share the FW download llink.
From TPLink - We recently released a beta firmware for Archer MR600(EU) V1 which can allow us to select 4G+bands for Archer MR600 manually.
https://static.tp-link.com/2020/202004/20200420/Archer_MR600v1_1.1.0_0.9.1_[200417-rel75138]_up_boot_2020-04-20_08.44.31.zip
For Archer MR600, if you want to use its 4G+network, your SIM card should support the CA bands group Archer MR400 supports. Please check the attached picture and check if your SIM card supports the band groups on the list or not.
They asked me to state that, this BETA FW is for the Archer MR600(EU) V1 ONLY!
Neither TPLink nor me take any respnsbility if you flash a none-EU router.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi, the band selection for Archer MR600 V1 would list all the bands it supported for aggregation, but the final LTE band aggregation is mainly decided by the ISP LTE Tower;
And May I know the internet bandwidth when it is on the band 20+3?
Thank you very much.
- Copy Link
- Report Inappropriate Content
so my provider is forcing my modem to switch its band when no device has an active internet connection?
with b20 and b3 im having 80mbit down and 30mbit up
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Hi TP-Link Support,
When we can expect official firmware with band selection for MR600?
- Copy Link
- Report Inappropriate Content
I have been in contact with them via chat and had emails from engineers. Depending on who you talk to some are saying there will be an official firmware and some are saying there won't. Terrible service from tp link, I should have returned this in December when I bought it, it only aggregates a fraction off the band combinations that the v2 does, and it cannot be fixed with firmware update.
- Copy Link
- Report Inappropriate Content
Is any updated beta firmware for MR 600 V1? can you share the link to download the latest one.
- Copy Link
- Report Inappropriate Content
Lets Down vote all their product on e-commence website, Tell people TP-Link is worst. TP-Link does not provide support and aftrsale service is really bad. 
- Copy Link
- Report Inappropriate Content
"Codice Open Source (GPL)
I prodotti TP-LINK contengono software sviluppato da terze parti, incluso software distribuito con licenza GPL (GNU General Public Licence versione 1, 2 o 3) o con licenza LGPL (GNU Lesser General Public License): l'utilizzo di questo software è possibile entro limiti e condizioni stabiliti dalla tipologia di licenza con la quale è distribuito e specificate a questo link. È possibile ottenere il codice sorgente soggetto a GPL e la lista dei prodotti che utilizzano tale codice all'interno del Centro sorgenti GPL.
I relativi software sono distribuiti con formula di TOTALE ESCLUSIONE DI GARANZIA; non sono pertanto garantite COMMERCIABILITÀ e/o IDONEITÀ PER QUALSIASI UTILIZZO SPECIFICO."
"Codice Open Source (GPL)
TP-Link products contain software developed by third parties, including software distributed with GPL license (GNU General Public License version 1, 2 or 3) or with LGPL license (GNU Lesser General Public License): the use of this software is possible Within limits and conditions established by the type of license with which it is distributed and specified at this link. You can get the source code subject to GPL and the list of products that use this code within the GPL source center. The relative software are distributed with a total guarantee exclusion formula; They are therefore not guaranteed marketability and / or suitability for any specific use."
- Copy Link
- Report Inappropriate Content
@darant Hi I'm new to the banding fun but im on Vodafone using the MR600 I'm planning on installing the V2 firmware on my V1 but I'm at a loss to which bands are which, can you help in any way please.
Also is there a newer version out now to do this?
Thanks
- Copy Link
- Report Inappropriate Content
HI, the beta firmware that added band selection for Archer MR600 V1:
and the official firmware for Archer MR600 V2 is already released:
https://www.tp-link.com/en/support/download/archer-mr600/v2/#Firmware
@badbackbilly, the firmware of V2 could not be installed on the V1;
As for the official firmware for V1 to support band selection, I am sorry that there is no ETA yet and please keep attention to the official website;
PS: since this thread is long enough, the beta firmware has been posted at the beginning of the thread;
If you have some other issues, it is recommended to start a new thread or leave me a private message for notice:
Thank you.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 13
Views: 193999
Replies: 511
Voters 10
