Deco M4 select signal source

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
123...

Deco M4 select signal source

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Deco M4 select signal source
Deco M4 select signal source
2021-02-18 08:58:25 - last edited 2022-03-01 06:51:31
Model: Deco M4  
Hardware Version: V2
Firmware Version: 1.4.3 20200918 Rel 74289

I got 3 deco M4 device, 1 as main (AP mode) and slave 1 and slave 2. 

Main deco and slave 1 are located at ground floor while slave 2 is located at floor 1. 

 

Main deco is located under the stair so the signal strength is weak a bit, but the speedtest done when client device connect to slave 1 still good. 

 

Problem here is slave 2 connect to main deco instead of slave 1 when slave 1 have greater signal strength compare to main deco. 

 

I saw another post Deco M5 source signal selectable? got release beta firmware for M5 model. 
May i know when will m4 beta firmware release? or does it have any other temporary solution?

  9      
  9      
#1
Options
1 Accepted Solution
[Solution] Deco M4 select signal source-Solution
2021-05-08 03:12:57 - last edited 2021-12-17 09:14:23

@Nicgou 

Hi All,

Currently, We are working on the firmware that supports selecting signal sources manually.

Please keep an eye on Deco APP and once we release the new firmware, you will get a notification.

For more details, please refer to this link:

[Deco] Manual Signal Source Selection

 

Thank you very much.

 

Recommended Solution
  2  
  2  
#25
Options
80 Reply
Re:Deco M4 select signal source
2021-02-22 21:56:12

@NoGameNoFun  i am also wondering this, has been driving me crazy... 

  1  
  1  
#2
Options
Re:Deco M4 select signal source
2021-02-24 14:34:10

@NoGameNoFun Same issue over here. I also saw there is a beta version for M5 but nothing for M4. 

 

I also saw you can turn the deco into an AP, but this applies to the hole network, not for a specific Node, which doesn't make sense at all...

https://www.tp-link.com/us/support/faq/1842/

  1  
  1  
#3
Options
Re:Deco M4 select signal source
2021-03-07 14:24:21
Just posted same issue for the m9. Hope this to be fixed soon.
  0  
  0  
#4
Options
Re:Deco M4 select signal source
2021-03-11 19:45:37
Same issue over here. Very disappointing
  0  
  0  
#5
Options
Re:Deco M4 select signal source
2021-03-22 09:41:16

@NoGameNoFun 

 

Same Issue and same hope reading the othet Thread.

  0  
  0  
#6
Options
Re:Deco M4 select signal source
2021-03-22 16:48:29

@NoGameNoFun 

Thank you for starting this topic for Deco M4, I am also interested to see how this could be solved.

 

  0  
  0  
#7
Options
Re:Deco M4 select signal source
2021-04-07 18:03:52 - last edited 2021-04-07 18:04:21

@mvstprn 

 

Same issue for my m4 deco devices. Looks like no any feedback from support team

  1  
  1  
#8
Options
Re:Deco M4 select signal source
2021-04-07 18:40:11

@GroupPolicy 

 

Have you tried to contact Deco support through the Deco app?

 

if you do this it will register a support case that is followed up by a support team.

 

I am currently running beta firmware that they shared and it looks like it is doing the job! 

  0  
  0  
#9
Options
Re:Deco M4 select signal source
2021-04-07 18:42:33

@mvstprn 

 

No, I Just check this topic, where is the beta version for m4? could you please share download link?

  0  
  0  
#10
Options
Re:Deco M4 select signal source
2021-04-07 18:44:16

@mvstprn 

 

Yes please share :)

  0  
  0  
#11
Options

Information

Helpful: 9

Views: 16269

Replies: 80

Related Articles