Range Extenders Support OneMesh/EasyMesh in AP Mode
Hey everyone!
We got some feedback from our community users requesting for Range Extender to support OneMesh/EasyMesh when works as an Access Point.
Currently, OneMesh/EasyMesh is not supported when the extender is set to Access Point Mode. However it is planned to support EasyMesh over Ethernet Backhaul under Range Extender mode.
It will start with RE315_V1 and gradually be added to other EasyMesh-supported extenders.
RE315 Supports EasyMesh Over Ethernet Backhaul
Note:
1. An extender needs to support EasyMesh (over Wi-Fi) first, then supports EasyMesh over Ethernet Backhaul.
2. Ethernet Backhaul only works when both your main router and satellite extender support EasyMesh over Ethernet Backhaul.
Other Mesh Options:
Option 1: Deco mesh system supports Ethernet backhaul under both Wireless Router and Access Point modes.
Deco Ethernet Backhaul feature and Topology
Kindly note that the Deco system is different from TP-Link OneMesh >>> TP-Link OneMeshâ„¢ VS Deco Mesh: What's the Difference?
Option 2: OneMesh---Compatible Powerline devices if your house is under the same power circuit/under the same power meter
Some powerline products could build OneMesh through Ethernet & house Power line
Powerline units that supports OneMesh
How to configure OneMesh with seamless roaming (Powerline Extender)
Related Articles:
Several questions about the OneMeshâ„¢ and Mesh
How to build an Ethernet Backhaul using TP-Link EasyMesh Range Extenders
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Hi David,
I can see the Archer AX72 does support easy-mesh on the 2023-07-07 firmware update, but what about the AX73-V1(EU)???
Are you planning to release the same features on the newer model firmware updates in the near future?
Cheers
N
- Copy Link
- Report Inappropriate Content
As of today's firmware update, the AX73 V1 does support EasyMesh.
Seems like the tpLink tech guys have responded to my previous post.
- Copy Link
- Report Inappropriate Content
@ All: AX73 EU v1 also has a firmware update to support "EasyMesh", but from what I read what "EasyMesh" is; still NO ethernet backhaul, so personally for me a worthless firmware update but maybe others are happy now.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
I have the following and support the implementation of OneMesh ethernet backhaul:
AX3000 Wi-Fi 6 Router
Hardware: Archer AX55 v1.0
Firmware: 1.2.3 Build 20230603 rel.46473(4555)
Country: AU
Wi-Fi Range Extender
Hardware: RE700X v1.0
Firmware: 1.1.4 Build 20230509 Rel. 78185
Country: AU
- Copy Link
- Report Inappropriate Content
I have EAP 225's in my house a great piece of kit. I recently decided I wanted to explore turning them into a mesh. I have hard wired these EAP's back to the switch connected to my router. I was more than a little bit surprised to learn that I could not mesh them in this config. As others had said I have thick walls and a big house, my office is 40m from the main building and a wireless mesh would be significantly reduced network speed. If you provide this feature I will purchase one of your routers immediately and mesh my entire property but without it I am stuck on separate SSID's because client roaming is not good enough.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 157
Views: 40844
Replies: 238