@Muscovite No probs, shame it didnt work out for you.

Out of interest, which router have you gone for?

  @Ian_D 

You'll get me banned on this website, after all I still have the x60 set... 

[SELF-CENSORED] RT-AX86U Pro

Ian_D wrote

  @Muscovite No probs, shame it didnt work out for you.

 

Out of interest, which router have you gone for?

  @David-TP 

I have a Deco X-55 and have tried to set up the VPN client using ExpressVPN using the OpenVPN protocol. Unfortunately, even though it says "Connected", I am not reaping the benefits of using a VPN.

Can you help?

  @David-TP 

Hi David, thank you for your reply. I just sent you an email.

  @David-TP 

Does this fix the hanging issue? I have the X50 firmware 1.2.2. Build 2023031 Rel. 53300 and unit 2 and 3

hangs once in a while and I need to power cycle the unit. This is a hassle because you

 have to physically do the reset. Thanks

David-TP wrote

Hello Everyone,

We are excited to announce the official firmware version 1.2.0 for Deco X50/Deco X55 V1 has been released last week. With this new firmware, you can now configure the VPN server/client, and other advanced features on the Deco.

 

Deco X50_V1_1.2.0 Build 20230113 ( for US/EU/JP/CA versions)
Deco X55_V1_1.2.0 Build 20230113 ( for US/EU/JP/CA versions)

>>How to update the firmware via web UI

 

Release Note:
New features:
1. Support for VPN server features, including Open VPN, PPTP VPN and L2TP/IPsec VPN.
2. Support for VPN client features, including Open VPN, PPTP VPN and L2TP/IPsec VPN.

3. Support for Static Route under Deco APP>More>Advanced.

4. Added the ability to customize the MTU size under Deco APP>More>Internet Connection>Internet Connection Type.

5. Added IOT network function.

 

* The following features(6-12) are also supported on 1.1.0 version:

6. Added Reboot Schedule for every day/week under Deco App > More > Reboot Schedule.
7. Added support for customizing Satellite Deco Signal Source under Deco App > Internet > Select the Satellite Deco > Signal Source.
8. Added support for customizing clients Connection Preference under Deco App > CLIENTS > Select the client > Click the gear icon on the right-up corner > Connection Preference.
9. Added No-IP and DynDNS to the DDNS settings under Deco App > More > Advanced > DDNS.
10. Added Smart DHCP on/off switch in Access Point mode under Deco App > More > Advanced > Smart DHCP.
11. Added a prompt notification when the Ethernet link rate goes down to 100Mbps.
12. Added schedule and bandwidth limit to guest network under Deco App > More > Wi-Fi > Guest Network.

 

Improvements:
1. Optimized the MAC Clone function.
2. Improved system reliability and security.

 

Note:
1. The Advanced features need to be configured on the Deco APP and please make sure your Deco APP is up to date.
2. Some new features would not be available when the router is working in Access Point mode.
3. The firmware downgrade needs to be performed by firmware recovery. >>How to use firmware recovery on Deco

 

 

Please feel free to comment below if there is any question about the new firmware.

David-TP wrote

Hello Everyone,

We are excited to announce the official firmware version 1.2.0 for Deco X50/Deco X55 V1 has been released last week. With this new firmware, you can now configure the VPN server/client, and other advanced features on the Deco.

 

Deco X50_V1_1.2.0 Build 20230113 ( for US/EU/JP/CA versions)
Deco X55_V1_1.2.0 Build 20230113 ( for US/EU/JP/CA versions)

>>How to update the firmware via web UI

 

Release Note:
New features:
1. Support for VPN server features, including Open VPN, PPTP VPN and L2TP/IPsec VPN.
2. Support for VPN client features, including Open VPN, PPTP VPN and L2TP/IPsec VPN.

3. Support for Static Route under Deco APP>More>Advanced.

4. Added the ability to customize the MTU size under Deco APP>More>Internet Connection>Internet Connection Type.

5. Added IOT network function.

 

* The following features(6-12) are also supported on 1.1.0 version:

6. Added Reboot Schedule for every day/week under Deco App > More > Reboot Schedule.
7. Added support for customizing Satellite Deco Signal Source under Deco App > Internet > Select the Satellite Deco > Signal Source.
8. Added support for customizing clients Connection Preference under Deco App > CLIENTS > Select the client > Click the gear icon on the right-up corner > Connection Preference.
9. Added No-IP and DynDNS to the DDNS settings under Deco App > More > Advanced > DDNS.
10. Added Smart DHCP on/off switch in Access Point mode under Deco App > More > Advanced > Smart DHCP.
11. Added a prompt notification when the Ethernet link rate goes down to 100Mbps.
12. Added schedule and bandwidth limit to guest network under Deco App > More > Wi-Fi > Guest Network.

 

Improvements:
1. Optimized the MAC Clone function.
2. Improved system reliability and security.

 

Note:
1. The Advanced features need to be configured on the Deco APP and please make sure your Deco APP is up to date.
2. Some new features would not be available when the router is working in Access Point mode.
3. The firmware downgrade needs to be performed by firmware recovery. >>How to use firmware recovery on Deco

 

 

Please feel free to comment below if there is any question about the new firmware.

  @Ian_D 

Hi Ian it's been pretty quiet for a week or so.

Has there been any forward progress on the VPN client issues?

Thanks,

Mark

Hello,

Is this SW available for Deco X90? Because I am planning on getting a 2.5G fiber connection.

Thank you,

Adrian

  @David-TP 

When is this going to be available for X50 PoE HW version 1.6?  Roughly speaking... this summer?  next year?

  @Mbauer5 Hi Mark, still waiting for a beta version to test. Mine is working fine using OpenVPN with a modified config file & debug firmware.

It did take many hours though to identify the issue make it work.

Hopefully we will see a beta version soon.

One thing I have noticed though, the VPN throughput is very slow, max throughput for me via the VPN tunnel is 20 Mbits which is a concern.