RE300 password issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

RE300 password issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
RE300 password issue
RE300 password issue
2023-03-07 16:42:44 - last edited 2023-03-30 09:15:28
Tags: #Highlighted Thread #undefined wireless password

Trying to set up an RE300 with a vr400 router.

 

Every method I try results in the extended networks having a non changeable password of ?undefined?.

 

No matter what I do I cannot get the RE300 to inherit the router password.

 

Both onemesh compatible allegedly.

 

If I actually use ?undefined? to connect to the extended network it works.

 

Help!

  0      
  0      
#1
Options
1 Accepted Solution
Re:RE300 password issue-Solution
2023-03-08 06:57:04 - last edited 2023-03-30 09:13:47

  @Sanofian 

Update:

Issue Description:

Recently, Some customers reported after configuring the range extender with our DSL model, like RE300 with VR400 V3 here, the WiFi name of RE might become TP- Link_XXXX and the WiFi password becomes? undefined? as shown in the figure below.

 

 

Available Solutions

 

This problem only happens to the DSL routers which have pre-configured with Aginet Config and will be fixed in the future official firmware.

 

Before the release of the official firmware, please refer to the following suggestions:

  • Please record the current WiFi name and WiFi password of the DSL modem.
  • Then change the WiFi name and WiFi password on the DSL modem router to something else.
  • After that, change the WiFi name and password back to the original.
  • Then reconfigure the range extender again---TP-Link Range Extender Setup (Range Extender Mode)

 

 

 

 

Recommended Solution
  0  
  0  
#2
Options
4 Reply
Re:RE300 password issue-Solution
2023-03-08 06:57:04 - last edited 2023-03-30 09:13:47

  @Sanofian 

Update:

Issue Description:

Recently, Some customers reported after configuring the range extender with our DSL model, like RE300 with VR400 V3 here, the WiFi name of RE might become TP- Link_XXXX and the WiFi password becomes? undefined? as shown in the figure below.

 

 

Available Solutions

 

This problem only happens to the DSL routers which have pre-configured with Aginet Config and will be fixed in the future official firmware.

 

Before the release of the official firmware, please refer to the following suggestions:

  • Please record the current WiFi name and WiFi password of the DSL modem.
  • Then change the WiFi name and WiFi password on the DSL modem router to something else.
  • After that, change the WiFi name and password back to the original.
  • Then reconfigure the range extender again---TP-Link Range Extender Setup (Range Extender Mode)

 

 

 

 

Recommended Solution
  0  
  0  
#2
Options
Re:RE300 password issue
2023-03-08 08:39:23

  @David-TP 

 

I tried using WPS, Web and tether app.

 

None work.

 

Web I actually had the opportunity to input the host router password but it still did not update the extended network password. 

  0  
  0  
#3
Options
Re:RE300 password issue
2023-03-14 19:52:19

  @David-TP

 

Bump.

 

Any resolution?

 

Really need this resolved.

  2  
  2  
#4
Options
Re:RE300 password issue
2023-03-16 03:11:35 - last edited 2023-03-20 11:03:31

  @Sanofian 

update:

Thank you very much for your time and patience.

I see your case has been forwarded to the senior engineers already for further assistance.

Please check the email for more suggestions.

Best regards.

 

  0  
  0  
#5
Options