Home Network Community > DSL Modem Routers > 'Authentication failed, Server TLS version is too low' appears when connecting OpenVPN of DSL Modem
< DSL Modem Routers

Solution 'Authentication failed, Server TLS version is too low' appears when connecting OpenVPN of DSL Modem

123

Solution 'Authentication failed, Server TLS version is too low' appears when connecting OpenVPN of DSL Modem

Solution'Authentication failed, Server TLS version is too low' appears when connecting OpenVPN of DSL Modem
'Authentication failed, Server TLS version is too low' appears when connecting OpenVPN of DSL Modem
2023-11-17 10:01:00 - last edited 2023-11-17 11:48:13
Tags: #VPN #Official

This Article Applies to:

Archer VR2100 V1, VR2100v V1, VR600 V3, VR400 V3, VR2800 V1

 

Issue Description:

After updating the OpenVPN client version, some users might be unable to connect to the OpenVPN server of DSL modem router, and OpenVPN client prompts "Authentication failed, and Server TLS version is too low".

 

Solutions:

1. For Archer VR2100 V1 and VR400 V3, please try installing the following beta firmware:

For VR2100 V1: Archer_VR2100_V1_1.8.0_Build_231114

For VR400 V3: Archer_VR400_V3_1.6.0_Build_231024

 

Note: Please be sure you have read the Terms and Conditions for TP-Link Beta Firmware before proceeding.

 

2. For all models, please open the OpenVPN Connect client >> click the three-line symbol in the upper left corner >> Settings >> Slide to the bottom to find the Advanced Settings >> Set Minimum TLS Version to TLS1.0, then test if it will be able to connect the OpenVPN Server properly.

 

If there is any further issue, please leave us your comment and provide the following information:

1) Model no., hardware and firmware version of your TP-Link DSL modem router

2) The version of your OpenVPN Client software

3) Screenshot of the error message and also the Minimum TLS Version

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  5      
 
  5      
 
#1
Options
26 Reply
Re:'Authentication failed, Server TLS version is too low' appears when connecting OpenVPN of DSL Modem
2023-11-19 10:12:21

  @Sunshine 

 

Settings Dialog in actual Client (3.4.2) is different!

You have to switch to "Insecure", this allows TLS 1.0.

Connection is working with this Setting.

 

  5  
  5  
#2
Options
Re:'Authentication failed, Server TLS version is too low' appears when connecting OpenVPN of DSL Modem
2023-11-20 06:11:42

  @Gremnet 

 

Thanks a lot for sharing the new settings image on your Client (3.4.2), which will help others a lot.

 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#3
Options
Re:'Authentication failed, Server TLS version is too low' appears when connecting OpenVPN of DSL Modem
2023-11-23 13:05:30

  @Sunshine 

 

unfortunately the Beta Firmware for the VR2100v1 is rejected by the device with Error 4503.

 

update to the latest V 1.17 was no problem

 

so FW is now: 1.17.0 0.9.1 v009e.0 Build 230831 Rel.3356n

HW is: Archer VR2100v v1 00000000

  1  
  1  
#4
Options
Re:'Authentication failed, Server TLS version is too low' appears when connecting OpenVPN of DSL Modem
2023-11-24 02:06:26

  @Gremnet 

 

Hi, upon checking, 1.17.0 0.9.1 v009e.0 Build 230831 Rel.3356n is a firmware for Archer VR2100v(DE) V1, which is actually a different model from Archer VR2100 V1, that is why your VR2100v cannot install the beta firmware for VR2100, you could try the solution 2 to modify the OpenVPN Client settings.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#5
Options
Re:'Authentication failed, Server TLS version is too low' appears when connecting OpenVPN of DSL Modem
2024-01-04 09:01:44

  @Sunshine 

Thank you for the link of the latest beta version of the VR2100v DSL router.

 

I was wondering if there's a resolution implemented that allows accessing the router via OpenVPN but without activating the remote management option. I read quite a few posts regarding this issue and this request and I am myself of the opinion that OpenVPN alone allows a safe access to the router. But having the remote management option being enabled is much more a safety hazard because the webinterface is then being accessible from anywhere over the internet and only protected by a password. I rather prefer to allow a connection by OpenVPN and not allowing my router to respond at all from anywhere else on the internet.

 

Apologies for my short essay but it would be really, really great if such a resolution was implemented in this beta version and, of course, in the next stable :-)

 

TIA!

  0  
  0  
#21
Options
Re:'Authentication failed, Server TLS version is too low' appears when connecting OpenVPN of DSL Modem
2024-01-04 09:19:49

  @_Raspberry_ 

My workaround is to connect to VPN and use remote desktop to a computer local to router and access the router settings there. Not ideal, and requires a PC to be on but at least it is more secure. 

  1  
  1  
#22
Options
Re:'Authentication failed, Server TLS version is too low' appears when connecting OpenVPN of DSL Modem
2024-01-04 09:22:23

  @Sunshine 

Any update on when this new firmware for Archer VR2100 will be in the "stable" release? I would prefer not to install beta firmware for a production router.

 

Also an option to have a client list of username / passwords to log into the OpenVPN would be nice. 

  1  
  1  
#23
Options
Re:'Authentication failed, Server TLS version is too low' appears when connecting OpenVPN of DSL Modem
2024-01-11 11:13:19 - last edited 2024-01-11 11:13:41

  @Sunshine 

 

Is there no fix for the Archer VR 2800 coming? I see it's still listed as a current product on TP-Link's website and remains for sale. Enabling insecure protocols is not a suitable long term workaround for a VPN, TLS 1.0 has been deprecated for 3+ years now due to vulnerabilities and the current version TLS 1.3 has been in available for 5 years. Do TP-Link have plans to provide firmware that supports TLS 1.3?

  13  
  13  
#24
Options
Re:'Authentication failed, Server TLS version is too low' appears when connecting OpenVPN of DSL Modem
2024-01-28 13:06:38

  @Sunshine Hi,  The above files do not install on VR600.  I have downloaded the latest firmware from TP Link web site but it does not fix TLS problem.  

Can you please help?

  1  
  1  
#25
Options
Re:'Authentication failed, Server TLS version is too low' appears when connecting OpenVPN of DSL Modem
2024-01-28 13:22:45

  @stu1234 Hi,

stu1234 wrote

  @Sunshine 

 

Is there no fix for the Archer VR 2800 coming? I see it's still listed as a current product on TP-Link's website and remains for sale. Enabling insecure protocols is not a suitable long term workaround for a VPN, TLS 1.0 has been deprecated for 3+ years now due to vulnerabilities and the current version TLS 1.3 has been in available for 5 years. Do TP-Link have plans to provide firmware that supports TLS 1.3?

VR600 Fix is not available either,

Regards

  1  
  1  
#26
Options
123

Information

Helpful: 5

Views: 14991

Replies: 26

Tags

VPN Official
Related Articles
Server TLS version is too low.
5456 0
OpenVPN TLS Version error
9756 1
 OpenVPN Server TLS version is too low
1210 1
 OpenVPN TLS key negotiation failed
4263 0
 DDNS authentication failed NOIP
690 0
Archer MR600 - TLS handshake failed (OpenVPN connection problem)
4434 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.