Home Network Community > Deco > Deco P9 not utilizing Ethernet connection
< Deco

Deco P9 not utilizing Ethernet connection

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Deco P9 not utilizing Ethernet connection

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Deco P9 not utilizing Ethernet connection
Deco P9 not utilizing Ethernet connection
2023-11-28 06:43:43
Tags: #Installation #P9
Model: Deco P9  
Hardware Version:
Firmware Version: 1.1.4

Hi, 

I have 3 Deco P9 in WiFi Router mode. Issue is Unit 2 only being connect via WiFi despite having cabled powerline and Ethernet connection to router.

 

***
 

The setup:
 

Unit 1 (main, router)

- connected with Ethernet cable to internet provider's modem (has wifi capability but I suppose it is irrelevant as not utilized in P9-setup) 

 

Unit 2

- connected with Ethernet cable to internet provider's modem (and thus it should have direct cabled connection to Unit 1)

 

Unit 3

- just connected via Powerline 

 

***
 

The realized connection:

 

- Unit 2: only WiFi to Unit 1

 

- Unit 3: WiFi and Powerline to Unit 2

 

***
 

why is Unit 2 not using Powerline nor Ethernet?

  0      
 
  0      
 
#1
Options
10 Reply
Re:Deco P9 not utilizing Ethernet connection
2023-11-28 12:25:02

  @Fjeldsted 

 

Please run the following test: unplug Ethernet cable from Unit 2, power off Unit 2, power it back on. Wait for about an hour. After that, check in Deco app if Unit 2 established powerline link to Main Deco.

 

Based on results of this test I will be able to give you recommendations for Unit 2 connectivity over powerline and Ethernet. 

  1  
  1  
#2
Options
Re:Deco P9 not utilizing Ethernet connection
2023-11-29 03:32:39 - last edited 2023-11-29 03:34:49

  @Fjeldsted 

I think you might need to switch Deco P9 into Access Point mode.

When Deco is under wireless router mode, only one unit can be wired to the internet provider's wireless modem router directly.

By the way, Ethernet Backhaul is over Powerline and WiFi Backhaul. You will have either Ethernet Backhaul only, PLC/Wi-Fi, PLC only, or WiFi only

Thank you very much and best regards.

 

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶Deco X50-5G-V1-1.2.0 Supports WireGuard VPN, Hybrid Mesh and More Try to leave a Message if urgent help is required.
  0  
  0  
#3
Options
Re:Deco P9 not utilizing Ethernet connection
2023-11-29 05:07:14

  @Alexandre. Thank you!

still only WiFi. 

  0  
  0  
#4
Options
Re:Deco P9 not utilizing Ethernet connection
2023-11-29 05:08:53

  @David-TP thank you! 
What are the downsides of going to access point mode? Is mesh still available?

  0  
  0  
#5
Options
Re:Deco P9 not utilizing Ethernet connection
2023-11-29 07:19:21

  @Fjeldsted 

Hi, yes, Mesh will still be available.

As for the difference, you could refer to What’s the difference between Access Point mode and Router mode on the Deco?

Thank you very much and best regards.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶Deco X50-5G-V1-1.2.0 Supports WireGuard VPN, Hybrid Mesh and More Try to leave a Message if urgent help is required.
  0  
  0  
#6
Options
Re:Deco P9 not utilizing Ethernet connection
2023-11-29 19:56:48

  @David-TP I tried access point mode but no difference, with or without Ethernet cable I get only WiFi, no Powerline, no Ethernet. 

  0  
  0  
#7
Options
Re:Deco P9 not utilizing Ethernet connection
2023-11-30 00:01:42
Actually now there is no Powerline connection at all…
  1  
  1  
#8
Options
Re:Deco P9 not utilizing Ethernet connection
2023-11-30 02:15:15

  @Fjeldsted 

Hi, Thanks for the update.

Since satellite units works the same, if you switch the location of Unit 2 and 3, are you able to get unit 2 on Powerline Backhaul?

(Please still set them in Access Point mode and Keep the Ethernet cable unplugged.)

Wait for your reply and best regards.

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶Deco X50-5G-V1-1.2.0 Supports WireGuard VPN, Hybrid Mesh and More Try to leave a Message if urgent help is required.
  0  
  0  
#9
Options
Re:Deco P9 not utilizing Ethernet connection
2023-12-02 16:43:01 - last edited 2023-12-02 19:53:45

  @David-TP no luck, but interestingly they keep the connections as in the original locations. One is still stuck with WiFi only. 
I tried plugging it in very close to the main unit, but nothing changed. 
 

update;

I can get Ethernet to work on the on that had no issues with Powerline: 

 

  0  
  0  
#10
Options
Re:Deco P9 not utilizing Ethernet connection
2023-12-03 08:35:45

  @David-TP 

very disappointed in general.. it has now dropped the Ethernet connection and is going WiFi only 

  0  
  0  
#11
Options

Information

Helpful: 0

Views: 700

Replies: 10

Tags

Installation
P9
Related Articles
deco p9 ethernet backhaul
2893 0
Deco P9 ethernet not working?
772 0
Ethernet connection on P9 V2 not working.
865 0
Deco P9 unstable connection
9554 1
Deco P9 Ethernet backhaul and guest network
1420 0
Can the Deco P9 work with powerline only connection
3406 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.