Business Community > WiFi > How to power the mesh AP
< WiFi

How to power the mesh AP

How to power the mesh AP

How to power the mesh AP
How to power the mesh AP
2024-06-06 20:45:46 - last edited 2024-06-07 05:47:45
Tags: #Mesh #Installation #Network Connectivity
Model: EAP225-Outdoor  
Hardware Version:
Firmware Version:

I am trying to wrap my head around this setup.

So here goes nothing.

I would like to use a software controller

TP-Link EAP225 Omada AC1350 Gigabit Wireless Access Point Business WiFi Solution w/ Mesh Support, wired to a POE switch. Then outisde my house I want to put a EAP225-Outdoor.

I want to use mesh to connect the 2 AP's. I am trying to figure out how to power the EAP 225 - Outdoor. Do you just use the injector that comse with it, but not plug a wire into the in side of the injector? 

Will all this work with the software controller?

 

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:How to power the mesh AP-Solution
2024-06-07 05:49:41 - last edited 2024-06-07 14:48:44

Hi  @Drj361 

 

I've given @Gnac's answer as a recommend solution.

 

Just leave the LAN port away, use PoE port to power on the mesh EAP. 

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#6
Options
5 Reply
Re:How to power the mesh AP
2024-06-06 21:15:29

  @Drj361 The poe switch will power them and you won't need the injectors.  Adopt them into your controller and the rest is history.

  1  
  1  
#2
Options
Re:How to power the mesh AP
2024-06-06 23:58:14

Hi  @Drj361 

 

EAP225-Outdoor can be powered on via both of the method.

 

Check instal guide of EAP225-Outdoor, there are two options.

 

 

 

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
  0  
  0  
#3
Options
Re:How to power the mesh AP
2024-06-07 03:25:33

  @Fae I guess I have not described the situation well enough. So the 225 out door is not connected to a lan. I understand that with mesh it should connect wirelessly to a wired AP.  And extend the signal. So my question is how do you power it. There is not a power cable that you plug into it. 

  0  
  0  
#4
Options
Re:How to power the mesh AP
2024-06-07 04:41:20 - last edited 2024-06-07 14:48:53

  @Drj361 Yes, you can power it by running an ethernet cable from the poe side of the injector and leave the lan side open.  

  1  
  1  
#5
Options
Re:How to power the mesh AP-Solution
2024-06-07 05:49:41 - last edited 2024-06-07 14:48:44

Hi  @Drj361 

 

I've given @Gnac's answer as a recommend solution.

 

Just leave the LAN port away, use PoE port to power on the mesh EAP. 

>> Omada EAP Firmware Trial Available Here << *Try filtering posts on each forum by Label of [Early Access]*
Recommended Solution
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 577

Replies: 5

Tags

Mesh Installation Network Connectivity
Related Articles
 no power ap mesh
665 0
extending the network with the AP 225 outdoor.
328 0
Mounting AP under the eave of the roof
462 0
Wired vs. wireless uplink / mesh enforcement
150 0
 Mesh network
191 0
Mesh
1646 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.