Official Release Deco X50/X55_V1_1.6.7 Optimized the Client Network Stability
This Article Applied to:
Deco X50/X55_V1_1.6.1/1.6.4
Modifications and Bug fixes:
- Supported EasyMesh
- Supported TSS_V2(TP-Link Simple Setup) function, which enables thed device to quickly discover and pair with TP-Link smart home and EasyMesh-compatible devices.
- Fixed the bugs of frequent client disconnections;
- Fixed the bug that clients cannot access the Internet after enabling the DoH server.
Download Link：
| Deco X50/X55_V1/V1.6 | 1.6.7_build20250314_Official |
Update Advice:
1. How to manually update the firmware via web UI- How to Update the Firmware of Deco.
2. The 1.6.7 could revert to the official 1.6.3/1.6.1 directly via web UI.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
xplodzs wrote
the problem with the missing devices continues. I have already rebooted the devices. deleted them from the deco app list. but some devices work, but are not reflected in the program. And in firmware 1.6.7, notifications appeared on DFS, the channel decreased from 160 mhz to 80 mhz. this did not happen before. I tried to return it back. but the router says that an error occurred. probably it is impossible to return it now?
Do you still remember the original firmware before 1.6.7?
I don't think the DFS is triggered by the firmware upgrade. How often would Deco report detecting a DFS signal?
Wait for your reply.
Best regards.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
1 this was not the case with firmware 1.6.1. after a couple of reboots, the problem no longer appeared on 1.6.7. and the channel itself became 160mhz/
2. The problem of disappearing devices in firmware 1.6.7 continues. I sent the logs by mail to feedback.deco@tp-link.com
I just went back to firmware 1.6.1 / didn't even need a reset deco x50 /restart secondary X20v4(1.5.5 FW) or clearing app client list.
the app immediately worked correctly for everyone who was connected and disconnected
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@xplodzs You can install 1.6.1 again by using Web UI
- Copy Link
- Report Inappropriate Content
@ARGamingPK1 logical. but why distribute firmware 1.6.4, which had errors and now they are testing 1.6.7. and 1.6.4 (non official ) was not even posted on the site?
- Copy Link
- Report Inappropriate Content
@xplodzs Hmmm i think you should go back to 1.6.1
- Copy Link
- Report Inappropriate Content
@David-TP I think I fixed my problem. It turns out that my old network was in the app and some of the devices were reflected there. I used the instructions https://community.tp-link.com/en/home/forum/topic/770972, deleted the network. And all the devices appeared on firmware 1.6.7. Maybe it's a coincidence. But it helped me
- Copy Link
- Report Inappropriate Content
@David-TP
Turning on the EasyMesh function at settings will caused my third party Easy-Mesh router to fall back to 40Mhz, by default, this Fiberhome router that I'm using is AX3000 rated and can broadcast 160mhz, but with this new firmware, the easymesh becomes weird when not ethernet backhaul, as it will drop connections between the decos with this router.
And when I use ethernet backhaul, the signal and data is stable but the router goes into slow mode unless I turn off the easy mesh and use WPS to link it as a client.
- Copy Link
- Report Inappropriate Content
Hi, can I have the model number of the third-party Easy-Mesh router?
Did you plan to set Deco as an EasyMesh agent or an EasyMesh controller?
Best reagrds.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 1
Views: 21651
Replies: 119
Voters 0
No one has voted for it yet.