Home Network Community > Deco > How To connect a Deco X50 5G with a Fritzbox 7490 with WireGuard as Router <-> Router Connection
< Deco

How To connect a Deco X50 5G with a Fritzbox 7490 with WireGuard as Router <-> Router Connection

How To connect a Deco X50 5G with a Fritzbox 7490 with WireGuard as Router <-> Router Connection

How To connect a Deco X50 5G with a Fritzbox 7490 with WireGuard as Router <-> Router Connection
How To connect a Deco X50 5G with a Fritzbox 7490 with WireGuard as Router <-> Router Connection
2025-07-05 14:26:18 - last edited 2025-08-06 08:04:45
Tags: #Network Connectivity #WireGuard
Model: Deco X50-5G  
Hardware Version: V1
Firmware Version: Current

I want to connect a Deco X50G with a Fritzbox. Currently i configured the X50-5G as VPN Client which works, but only one way...

 

i can ping my systems at home, but i cannot ping devices in the x50 network.

 

is there any how to avaiable?

 

connecting to fritzbox is a no-brainer with wireguard. i guess it's only a smal thing.

 

configuring deco as VPN server leads to a config, which is refused by fritzbox to be imported...

 

what i want to do is the following

 

deco x50g with local internet link, fritzbox at home with local internet uplink, both sould establish a wireguard connection, so that all devices on both sites can reach each other. with two fritzboxes this works fine. the question is how to configure it between deco and fritzbox

  0      
 
  0      
 
#1
Options
2 Accepted Solutions
Re:How To connect a Deco X50 5G with a Fritzbox 7490 with WireGuard as Router <-> Router Connection-Solution
2025-07-29 10:00:56 - last edited 2025-08-06 08:04:45

  @SvenKoehler 

Hi, thank you very much for your feedback.

Deco doesn't support site-to-site VPN.

So when Deco X50-5G is set as the WireGuard VPN clients, the selected devices can access the local network of Fritzbox, but not the other way around.

I think your Deco X50-5G uses CG-NAT, and the current IPV4 address is a reserved IP address. When it was configured as the WireGuard VPN server, it was behind the NAT firewall of the SIM carrier.

Best regards.

 

 

▶Check What's Currently Going on With Deco ▶Deco BE85 1.2.0 Enhanced Mesh Backhaul Stability and Device Roaming Experience ▶Deco BE65/BE65 Pro 1.2.0 Enhanced Mesh Network Stability and System Security ▶Deco BE75 1.1.0 Added WireGuard VPN, Manual Channel Selection and More Try to leave a Message if urgent help is required.
Recommended Solution
  0  
  0  
#2
Options
Re:How To connect a Deco X50 5G with a Fritzbox 7490 with WireGuard as Router <-> Router Connection-Solution
15 hours ago - last edited 15 hours ago

  @David-TP the gl inet x-3000 5G router supports it, i chose deco because of it other awesome features. can you put it on the wishlist...?

Recommended Solution
  0  
  0  
#3
Options
3 Reply
Re:How To connect a Deco X50 5G with a Fritzbox 7490 with WireGuard as Router <-> Router Connection-Solution
2025-07-29 10:00:56 - last edited 2025-08-06 08:04:45

  @SvenKoehler 

Hi, thank you very much for your feedback.

Deco doesn't support site-to-site VPN.

So when Deco X50-5G is set as the WireGuard VPN clients, the selected devices can access the local network of Fritzbox, but not the other way around.

I think your Deco X50-5G uses CG-NAT, and the current IPV4 address is a reserved IP address. When it was configured as the WireGuard VPN server, it was behind the NAT firewall of the SIM carrier.

Best regards.

 

 

▶Check What's Currently Going on With Deco ▶Deco BE85 1.2.0 Enhanced Mesh Backhaul Stability and Device Roaming Experience ▶Deco BE65/BE65 Pro 1.2.0 Enhanced Mesh Network Stability and System Security ▶Deco BE75 1.1.0 Added WireGuard VPN, Manual Channel Selection and More Try to leave a Message if urgent help is required.
Recommended Solution
  0  
  0  
#2
Options
Re:How To connect a Deco X50 5G with a Fritzbox 7490 with WireGuard as Router <-> Router Connection-Solution
15 hours ago - last edited 15 hours ago

  @David-TP the gl inet x-3000 5G router supports it, i chose deco because of it other awesome features. can you put it on the wishlist...?

Recommended Solution
  0  
  0  
#3
Options
Re:How To connect a Deco X50 5G with a Fritzbox 7490 with WireGuard as Router <-> Router Connection
15 hours ago

  @David-TP 

 

moreover - what would you recommend as alternative mitigation until this feature will come? i recommend to implement it

  0  
  0  
#4
Options

Information

Helpful: 0

Views: 151

Replies: 3

Tags

Network Connectivity WireGuard
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.