Home Network Community > Wi-Fi Routers > Mutltiple issues incluing Vowifi etc. in Archer AX10 router
< Wi-Fi Routers

Mutltiple issues incluing Vowifi etc. in Archer AX10 router

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Mutltiple issues incluing Vowifi etc. in Archer AX10 router

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Mutltiple issues incluing Vowifi etc. in Archer AX10 router
Mutltiple issues incluing Vowifi etc. in Archer AX10 router
2025-08-04 16:06:57 - last edited 2025-09-04 10:23:42
Tags: #Network Connectivity #Firmware Update
Model: Archer AX1500  
Hardware Version: V2
Firmware Version: 1.3.11 Build 20250325 Rel. 24737(5553)

Why not VoWifi not working on my router, where as any other tp-link routers are VoWifi Ready Out-of-the-box. 

 

And also explain and give a solution for that.

 

Also I'm using Smart network, which I felt like an issue like switching off the 2.4Ghz network for some frequent times a week. Is this any kind of a manufacturing issue??

Also Currently I'm having issue where if I move min 3 meters away from the router and the signal strength gets down to 50% the internet speed dropped to 20% of what near the router. What's that issue?? It has never been there before the latest firmware update.

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:Mutltiple issues incluing Vowifi etc. in Archer AX10 router-Solution
2025-08-05 03:10:32 - last edited 2025-09-04 10:23:42

Hello@Kratosin ,

Welcome to our community.

 

Did you update the firmware recently? When did the issue start occurring?

 

If your phone is facing issues with Wi-Fi calling when connecting to the TP-Link Archer Router, please follow the steps below:
    1) Verify that your ISP (Internet Service Provider) offers Wi-Fi calling service and ensure that the Wi-Fi calling option is enabled in your phone's settings.
    2) Disable SIP ALG. Please log in to the router's web management interface, go to Advanced > NAT Forwarding > ALG, disable the "SIP ALG", and save the settings.
    3) Reserve the IP address for your phone and Enable port forwarding for UDP port 500 and port 4500. Go to Advanced > Network > DHCP Server > add an address reservation entry in the Address Reservation section. Go to Advanced > NAT Forwarding > Port Forwarding to configure port forwarding.
    4) For further detailed troubleshootings, please refer to this FAQ: What should I do if Wi-Fi calling cannot work through TP-Link wireless router?

Welcome to Our Community！ Check Out the Latest Posts: △New Firmware for Archer BE400 V1 to Support IPv6 VPN, Wake On LAN, and More △New Firmware for Archer BE800 V1 to Support VPN Merge, EasyMesh Guest/IoT Network Extend, and More △Enhanced EasyMesh Support with Extended Guest/IoT/MLO Networking and Advanced Features for BE550 V2 △New Firmware for Archer BE900 V2 to Support Multi-WAN, DoH/DoT, EasyMesh in AP Mode and More If you found the post or response helpful, click Helpful. If an answer solves your problem, click Recommended Solution so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
1 Reply
Re:Mutltiple issues incluing Vowifi etc. in Archer AX10 router-Solution
2025-08-05 03:10:32 - last edited 2025-09-04 10:23:42

Hello@Kratosin ,

Welcome to our community.

 

Did you update the firmware recently? When did the issue start occurring?

 

If your phone is facing issues with Wi-Fi calling when connecting to the TP-Link Archer Router, please follow the steps below:
    1) Verify that your ISP (Internet Service Provider) offers Wi-Fi calling service and ensure that the Wi-Fi calling option is enabled in your phone's settings.
    2) Disable SIP ALG. Please log in to the router's web management interface, go to Advanced > NAT Forwarding > ALG, disable the "SIP ALG", and save the settings.
    3) Reserve the IP address for your phone and Enable port forwarding for UDP port 500 and port 4500. Go to Advanced > Network > DHCP Server > add an address reservation entry in the Address Reservation section. Go to Advanced > NAT Forwarding > Port Forwarding to configure port forwarding.
    4) For further detailed troubleshootings, please refer to this FAQ: What should I do if Wi-Fi calling cannot work through TP-Link wireless router?

Welcome to Our Community！ Check Out the Latest Posts: △New Firmware for Archer BE400 V1 to Support IPv6 VPN, Wake On LAN, and More △New Firmware for Archer BE800 V1 to Support VPN Merge, EasyMesh Guest/IoT Network Extend, and More △Enhanced EasyMesh Support with Extended Guest/IoT/MLO Networking and Advanced Features for BE550 V2 △New Firmware for Archer BE900 V2 to Support Multi-WAN, DoH/DoT, EasyMesh in AP Mode and More If you found the post or response helpful, click Helpful. If an answer solves your problem, click Recommended Solution so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options

Information

Helpful: 0

Views: 371

Replies: 1

Tags

Network Connectivity Firmware Update
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.