HX710-Pro not working correctly as a mesh network
I have a mesh network setup with two of the above devices, and EX820v Router and also a HX710 with different firmware - 0.2.0 3.0.0 v6082.0 Build 240806 Rel.7178n
I have BRSK broadband but the 3 HX710Pro were bought from ebay and two of them have the BRSK branding on them, and the Build 240806 Rel.7178n does not.
They are not always functioning correctly as a mesh network. My phone sometimes fails to remain connected to wifi when I go from downstairs to upstairs or vice versa and I'm wondering if this is because of the different firmware versions.
If so, is it possible to change the firmware on the device with firmware "Build 240806 Rel.7178n" so that it matches the others?
Many thanks,
Damian
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
For anyone else having similar issues, I eventually found what the issue was. I turned off the GI setting (guard interval) on my router and the mesh is now functioning correctly. I also turned fast routing on.
- Copy Link
- Report Inappropriate Content
Hi, welcome to the community.
Did you add all 3 HX710 pro units to the EasyMesh network of EX820v?
Did the failure of seamless roaming on the mobile phone always happen when moving between HX710 Pro_Build 241105 and HX710 Pro_Build 240806?
Could the mobile phone automatically roam between EX820v and HX710 pro?
How about other mobile devices? Did they run into a similar issue?
I don't think the reported issue is related to different firmware versions. EasyMesh is advertised to establish a seamless wireless connection throughout your home among the EasyMesh router and extenders. There are even different models involved.
Wait for your reply.
Best regards.
- Copy Link
- Report Inappropriate Content
@David-TP
Hi David,
Many thanks for getting back to me about this.
Yes, all three HX710 Pro units were added via the EX820v EasyMesh network, and all are reporting no problems within the Aginet App.
The issue with phones WiFi failing to automatically reconnect to different units in the mesh system affects multiple mobile phones within the household. The issue is intermittent and so it is difficult to say if it is only happening when the phones are roaming between specific units. When it does occur, the phone will say "obtaining IP address" and remain stuck on this until I turn WiFi off and on. I have just tried to replicate the issue but, of course, it didn't happen!
In the Aginet App the connection diagram is a straight line which shows EX820v -> HX710 Pro (EU1) -> HX710 Pro (GBBRSK) -> HX710 Pro (GBBRSK)
So the GBBRSK units are passing through the EU1 unit. I thought that the different firmware of the EU1 unit may be the cause of this issue.
Many thanks,
Damian
- Copy Link
- Report Inappropriate Content
For anyone else having similar issues, I eventually found what the issue was. I turned off the GI setting (guard interval) on my router and the mesh is now functioning correctly. I also turned fast routing on.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
@DamianTP
I have this too
But its also laptops and tablets.
I also have different firmware versions
I'd like to update them all to the same but I cant fond the files
Be nice to get some ansers
Hoping ur trick works, im guessing you meant fast roaming not routing?
- Copy Link
- Report Inappropriate Content
Hi, it would be better to start a new thread here with more details:
https://community.tp-link.com/en/home/forum/edit/topic?moduleId=39
such as:
How about the model numbers of the EasyMesh Controller and Agent? Or are there only HX710 Pro units?
Are the HX710 Pro units offered by the ISP? How about their firmware versions?
How do the laptops and tablets behave over the Mesh network?
Thank you very much.
Best regards.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 1
Views: 477
Replies: 6
Voters 1