WPS Push Button does not work

WPS Push Button does not work

WPS Push Button does not work
WPS Push Button does not work
2025-11-02 03:03:31 - last edited 3 weeks ago
Model: VX420-G2h  
Hardware Version: V2
Firmware Version: 0.9.0 2.0.0 v603c.0

The WPS does not work -connect

USING THE Wireless- WPS- Advanced page 

 

When the web page connect button is pressed, it just keeps trying to connect.

The WPS continue to flash as expected, but does not connect.

 

Light stops flashing on the MODEM and the screen shows - 

 

Failed to add the device!

  0      
  0      
#1
Options
1 Accepted Solution
Re:WPS Push Button does not work-Solution
2025-11-20 07:40:28 - last edited 3 weeks ago

Hello @WAMalcolm2025 ,

Thanks for contacting our community.

 

Would you like to create an EasyMesh network between the modem and your extender? What is the model, hardware, and firmware version of your extender? 

Due to the asynchronous nature of EasyMesh technology, it is currently necessary to temporarily disable EasyMesh and conventionally configure the extender.

 

Here are the suggested steps to restore your network connection:

  • Please temporarily disable EasyMesh on the VX420-G2H. 
  • It is recommended that you reset the Range Extender entirely before the Quick Setup.
  • Then, perform the Quick Setup on the Range Extender

 

Please keep an eye out for the next official firmware update for the VX420-G2H, as this unexpected behavior will be corrected

 

For more details, please refer here.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: △Pre-release Firmware for Archer AX50 Introduces New Parental Control Features and Enhancements △Introducing AI QoS: Elevate Your Gaming Experience on the Archer GE800 Gaming Router △Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN △Tether KidShield Test Recruitment - Safeguarding Children's Online Experience If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#3
Options
2 Reply
Re:WPS Push Button does not work
2025-11-02 19:32:46

  @WAMalcolm2025 

 

When activate WPS on VX420-G2hyou will then have two minutes to press the physical WPS button on the client device to connect them.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#2
Options
Re:WPS Push Button does not work-Solution
2025-11-20 07:40:28 - last edited 3 weeks ago

Hello @WAMalcolm2025 ,

Thanks for contacting our community.

 

Would you like to create an EasyMesh network between the modem and your extender? What is the model, hardware, and firmware version of your extender? 

Due to the asynchronous nature of EasyMesh technology, it is currently necessary to temporarily disable EasyMesh and conventionally configure the extender.

 

Here are the suggested steps to restore your network connection:

  • Please temporarily disable EasyMesh on the VX420-G2H. 
  • It is recommended that you reset the Range Extender entirely before the Quick Setup.
  • Then, perform the Quick Setup on the Range Extender

 

Please keep an eye out for the next official firmware update for the VX420-G2H, as this unexpected behavior will be corrected

 

For more details, please refer here.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: △Pre-release Firmware for Archer AX50 Introduces New Parental Control Features and Enhancements △Introducing AI QoS: Elevate Your Gaming Experience on the Archer GE800 Gaming Router △Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN △Tether KidShield Test Recruitment - Safeguarding Children's Online Experience If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#3
Options