Home Network CommunityWi-Fi Routers AX58 easymesh ethernet problem
Wi-Fi Routers

AX58 easymesh ethernet problem

AX58 easymesh ethernet problem

AX58 easymesh ethernet problem
AX58 easymesh ethernet problem
Wednesday - last edited Thursday
Tags: #EasyMesh #EasyMesh Ethernet Backhaul
Model: Archer AX58  
Hardware Version: V1
Firmware Version: Last

Hi, i have problems with ethernet easymesh.

My network is:

 

          NX500 Outdoor

               |  (Cat5 cable)

         AX55 Pro

               |  (Cat5 cable)

        TL-SG1016D switch

               |  (Cat5 cable)

         LS105G switch

               |  (Cat5 cable)

         AX58

 

 

The problem is that after a while, the AX58 switches from EasyMesh Ethernet to EasyMesh Wi-Fi with the AX55 Pro (the signal is very weak, but it can connect).

If I reboot the AX58, it goes back to EasyMesh Ethernet mode, but as mentioned, after a while it switches back to EasyMesh Wi-Fi.

This is very annoying. The CAT5 cables are fine, and I even replaced the switches (they're new).

I updated everything to the latest firmware version, which I found here in the forum on other topics.

If I don't find a solution, I'll return the products to Amazon.

Thanks

0
0
#1
3 Reply
Re:AX58 easymesh ethernet problem
Friday

Hello @Fra82 ,

Welcome to our community.

 

Here are some suggestions that may help you:

  • Please temporarily remove one switch and test the connection directly.
  • Check if the switch port status lights are stable.
  • Try changing the ports between switches.
  • Replace the Cat5e/Cat6 cables.

 

In particular:

  • The cables connecting the switches
  • The cables connecting the AX58 to the switches
  • It is recommended to replace all of them with Cat5e or Cat6 to ensure quality.
Welcome to Our Community! Get the latest posts: △New Firmware for Archer GE550/GE650 V1 Introduces AI-QoS, EasyMesh IoT Expansion, and More! △New Firmware Releases for Archer BE805 V1/BE450 V1 to Support VPN Merge, New ECO Mode, and More! More posts, please see: △ Get the Ongoing Pre-release Firmware for Wi-Fi Routers Here— Subscribe for Updates! Urgent problems with your Wi-Fi Router, Range Extender, or DSL Modem? Please reach out via private Messages or @Joesph-TP in your new thread directly. Click △ Or ☆Recommended Solution if the post/answer helps.
0
0
#2
Re:AX58 easymesh ethernet problem
Friday - last edited Friday

  @Joseph-TP 

 

1) I cannot remove switches because are in different house floor. Switches are new and i have same problems with old switches.

2) Port status lights are stable, no packet loss or ethernet stuck

3) I could try but i think is useless

4) Cable is working (how else would it work after every reboot?)

 

I think problem is in your firmware......

 

 

0
0
#3
Re:AX58 easymesh ethernet problem
Yesterday

Hello  @Fra82 ,

Thanks for getting back to us.

 

In that case, it appears your NX500-Outdoor is acting as the main router within the EasyMesh network—is that correct?
If it's convenient for you, could you swap the positions of the AX55 Pro and the AX58 to compare the results?

 

To help you efficiently, I've forwarded your case to the TP-Link support engineers, who will reach out to you using your registered email address later. Please keep an eye on your email inbox for follow-up.

 

Welcome to Our Community! Get the latest posts: △New Firmware for Archer GE550/GE650 V1 Introduces AI-QoS, EasyMesh IoT Expansion, and More! △New Firmware Releases for Archer BE805 V1/BE450 V1 to Support VPN Merge, New ECO Mode, and More! More posts, please see: △ Get the Ongoing Pre-release Firmware for Wi-Fi Routers Here— Subscribe for Updates! Urgent problems with your Wi-Fi Router, Range Extender, or DSL Modem? Please reach out via private Messages or @Joesph-TP in your new thread directly. Click △ Or ☆Recommended Solution if the post/answer helps.
0
0
#4

Information

Helpful: 0

Views: 140

Replies: 3

Tags

EasyMesh EasyMesh Ethernet Backhaul
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.