Extender does not show a network

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Extender does not show a network

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Extender does not show a network
Extender does not show a network
2019-01-04 19:49:34 - last edited 2021-06-15 08:18:02

Hi. I reset my wifi extender and now it does not link to a network. I turned it on and off several times. I restarted my router, but nothing.

Any suggestions?

 

  13      
  13      
#1
Options
1 Accepted Solution
Re:Extender does not show a network-Solution
2021-06-12 13:43:19 - last edited 2021-06-15 08:18:02

I'm not sure if this question is still active.

I had the same problem. After much searching I found that if I reset the extender (directions are in the quick installation guide) that my extender then once again showed up on my home network. From then on I was able to use Method ONE to reconnect my device.

 

My problem originated with the fact that I changed the name and password for my router due to weak security.

 

The method to reset or in this case restore is listed under 

Q2. How do I restore the extender to its factory default settings?

. With the extender powered on, use a pin to press and hold the Reset button until all the LEDs turn on momentarily, and then release the button.

 

I suppose the other option is to contact TP Link support, which I did not do, at:

http://www.tp-link.com/support

Recommended Solution
  15  
  15  
#5
Options
4 Reply
Re:Extender does not show a network
2019-01-05 08:43:27

I'm having this same issue on Tl-Wa750RE. Someone should assist please

  0  
  0  
#2
Options
Re:Extender does not show a network
2019-01-08 09:50:22

Hi,

 

You may refer to this troubleshooting guide 

 

https://www.tp-link.com/en/faq-2234.html

 

Hope it helps.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#3
Options
Re:Extender does not show a network-Solution
2021-06-12 13:43:19 - last edited 2021-06-15 08:18:02

I'm not sure if this question is still active.

I had the same problem. After much searching I found that if I reset the extender (directions are in the quick installation guide) that my extender then once again showed up on my home network. From then on I was able to use Method ONE to reconnect my device.

 

My problem originated with the fact that I changed the name and password for my router due to weak security.

 

The method to reset or in this case restore is listed under 

Q2. How do I restore the extender to its factory default settings?

. With the extender powered on, use a pin to press and hold the Reset button until all the LEDs turn on momentarily, and then release the button.

 

I suppose the other option is to contact TP Link support, which I did not do, at:

http://www.tp-link.com/support

Recommended Solution
  15  
  15  
#5
Options
Re:Extender does not show a network
2021-06-15 08:19:10

@KingFish Thanks for sharing~

  0  
  0  
#6
Options

Information

Helpful: 13

Views: 35304

Replies: 4

Related Articles