Middle LED on adapters keeps on going out

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Middle LED on adapters keeps on going out

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Middle LED on adapters keeps on going out
Middle LED on adapters keeps on going out
2020-03-08 12:08:22 - last edited 2021-02-03 12:48:05
Model: TL-PA8010 KIT  
Hardware Version:
Firmware Version:

The middle light keeps going out and I have paired my two adapters four times this morning and after they have paired I have put them back in the place they need to be and all three lights stay on for about ten minutes and then the middle one goes out can someone advise please.I pair them by doing the following.Plug them in next to each other then press the pair button on the first adapter wait for 120 seconds then press the pair button on the other adapter and then put them back where they should be.Does that sound correct.Do I have to press the pair button on thr third adapter which is connected to the router..How do I know what the Hardware and firmware versions are

  0      
  0      
#1
Options
1 Accepted Solution
Re:Middle LED on adapters keeps on going out-Solution
2020-03-09 08:22:02 - last edited 2021-02-03 12:48:05

@laserbeam 

 

Hello, below is the instruction to pair the powerline adapters. 

https://www.tp-link.com/support/faq/258/

 

You press the pair button of main adapter for 1s, with power led flashing, then you can press the pair button of the slave adapter for 1s, the power led should flash as well. You can wait 1-2 minutes to make them pair themselves.

 

If you have more than 2 adapters, you need repeat the steps above to pair the third unit. 

 

You can change another socket to plug the adapter and verify whether it is gone again. 

 

May it help. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
1 Reply
Re:Middle LED on adapters keeps on going out-Solution
2020-03-09 08:22:02 - last edited 2021-02-03 12:48:05

@laserbeam 

 

Hello, below is the instruction to pair the powerline adapters. 

https://www.tp-link.com/support/faq/258/

 

You press the pair button of main adapter for 1s, with power led flashing, then you can press the pair button of the slave adapter for 1s, the power led should flash as well. You can wait 1-2 minutes to make them pair themselves.

 

If you have more than 2 adapters, you need repeat the steps above to pair the third unit. 

 

You can change another socket to plug the adapter and verify whether it is gone again. 

 

May it help. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router Archer BE800 New Firmware Added Support for EasyMesh in AP Mode, DoH&DoT, and 3-Band MLO Connection Archer AX90 New Firmware Added Support for EasyMesh and Ethernet Backhaul If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options

Information

Helpful: 0

Views: 1187

Replies: 1

Related Articles