Home Network Community > All Threads > After setup in AP Mode, connection not stable, other issues
< All Threads

After setup in AP Mode, connection not stable, other issues

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

After setup in AP Mode, connection not stable, other issues

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
After setup in AP Mode, connection not stable, other issues
After setup in AP Mode, connection not stable, other issues
2020-09-25 15:16:18 - last edited 2020-09-27 09:57:27
Model: Deco M9 Plus  
Hardware Version: V2
Firmware Version: 1.2.12

Model: Deco M9 Plus

Hardware Version: V2

Firmware Version: 1.2.12

 

Hello - My iphone keeps connecting then disconnecting to WiFi frequently (every 5-10 seconds or so).  Other end points like iPad, Mac, PC, etc experience similar issues.

 

Setup is as follows:

 

DSL modem (C3000A)--wired cable--Deco(first floor)

                                    --wired cable--Deco(second floor)

                                    --wired cable--Deco(first floor, other side of home)

 

All three Deco's are hard wired directly to DSL modem using one port each of the 5 ports available on the DSL modem.

 

SSID/Password is set to the same on DSL modem and all three Decos including frequencies 2.4 and 5.0.  So same SSID/Password on everything.

 

Operating Mode = Access Point

Fast Roaming = Disabled

Beamforming = Enabled

 

Thanks in advance for input.

  0      
 
  0      
 
#1
Options
1 Accepted Solution
Re:After setup in AP Mode, connection not stable, other issues-Solution
2020-09-27 09:57:01 - last edited 2020-09-27 09:57:27

@Sctsdale 

 

Hello, the firmware of your Deco M9 Plus V2 is quite old, please refer to the below post to upgrade it first:

https://community.tp-link.com/en/home/forum/topic/212300?page=1

 

May it help~

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶Deco X50-5G-V1-1.2.0 Supports WireGuard VPN, Hybrid Mesh and More Try to leave a Message if urgent help is required.
Recommended Solution
  0  
  0  
#3
Options
2 Reply
Re:After setup in AP Mode, connection not stable, other issues
2020-09-26 13:00:18
I did another reboot of everything and on occasion now it drops the connection, says incorrect password, and asks to reenter the password. Same password is set for everything so not sure why it would say incorrect password. Any assistance would be great.
  0  
  0  
#2
Options
Re:After setup in AP Mode, connection not stable, other issues-Solution
2020-09-27 09:57:01 - last edited 2020-09-27 09:57:27

@Sctsdale 

 

Hello, the firmware of your Deco M9 Plus V2 is quite old, please refer to the below post to upgrade it first:

https://community.tp-link.com/en/home/forum/topic/212300?page=1

 

May it help~

▶Check What's Currently Going on With Deco ▶Deco Starts Supporting Changing Wireless Channels! ▶Deco X50-5G-V1-1.2.0 Supports WireGuard VPN, Hybrid Mesh and More Try to leave a Message if urgent help is required.
Recommended Solution
  0  
  0  
#3
Options

Information

Helpful: 0

Views: 713

Replies: 2

Related Articles
No internet in AP mode
987 2
Network not stable in AP mode
509 0
Deco M9 plus - is this AP setup possible?
1203 0
Pinging other devices in AP mode not possible
538 0
Deco M9+ as AP mode
793 0
Do I lose mesh functionality moving to AP mode.
704 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.