Is there any firmware to manually set a specific 4G band (MR6400) V.5

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Is there any firmware to manually set a specific 4G band (MR6400) V.5

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Is there any firmware to manually set a specific 4G band (MR6400) V.5
Is there any firmware to manually set a specific 4G band (MR6400) V.5
2020-10-18 02:31:19 - last edited 2021-03-17 07:46:05
Model: TL-MR6400  
Hardware Version: V5
Firmware Version: v5

Hi, 

I was unable to find a setting to manually force the use of a specific 4G band in my modem.

For example, sometimes the router uses the band 8 instead of 1/3/40 which are much more faster than the 8 one, resulting in a drastic reduce in network speed.  Band 3 in my country Indonesia can produce 30 Mbps meanwhile the band 8 only reaches 4 Mbps. It makes me and my friends very frustated with this situation.

I know for sure that with router of other brand like H is possible to set this option. Is it possible to enable it with next firmware update? 
We are in indonesia very need this feature, I hope TP-Link can release this feature in a few weeks forward. Don't take much time. Please push forward this issue to the software department ASAP.

 

Thanks

  3      
  3      
#1
Options
1 Accepted Solution
Re:Is there any firmware to manually set a specific 4G band (MR6400) V.5-Solution
2021-03-17 07:45:53 - last edited 2021-03-17 07:46:05
Recommended Solution
  0  
  0  
#8
Options
7 Reply
Re:Is there any firmware to manually set a specific 4G band (MR6400) V.5
2020-10-21 05:44:38

@Keripik_Kinta 

Thank you very much for your time and patience.

We do have the plan to release the firmware which supports manual band selection.

But the estimated date is still not clear.

For more updated news, please keep close attention to our official websites;

 

Thanks a lot.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#2
Options
Re:Is there any firmware to manually set a specific 4G band (MR6400) V.5
2020-11-18 15:56:22

@Sunshine we wait so long.. we cant live with this.. some of my friend in our 4g group already move to H brand.. please make it asap. thanks

  1  
  1  
#3
Options
Re:Is there any firmware to manually set a specific 4G band (MR6400) V.5
2020-11-19 11:49:31 - last edited 2020-11-19 11:51:17

@Keripik_Kinta 

 

Sorry for keeping you waiting, while we still have no ETA for the new firmware that supports band selection, it's expected to be released later this year, please kindly wait and pay your attention to the official website.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#4
Options
Re:Is there any firmware to manually set a specific 4G band (MR6400) V.5
2020-12-02 03:45:22

@Kevin_Z 

Hello


I just purchased MR6400 to replace the small huawei modem provided by my network operator.

Firware is up to date (1.1.0 0.9.1 v0001.0 Build 200511 Rel.43036n)

 

It’s all good until the speed drops dramatically, and after digging a little bit I see there is the same problem for almost all your modem... it constantly switch to the worst band (20) and there is no way to force it to the fastest bands (1/3/5).

 

Do we really have to beg on this forum for month until you finally realize how big this problem is?

How hard is it for you to implement that while you have done the exact same thing with other modems like the MR600?

 

I can’t believe what’s going on. It’s really a shame.

 

Please provide a firmware with the option to select band asap, without it the product is 99% useless.

Maybe as an in-between, you could make a firmware which simply doesn’t use the band 20?

 

Sincerely
Josh

 

  0  
  0  
#5
Options
Re:Is there any firmware to manually set a specific 4G band (MR6400) V.5
2020-12-03 03:00:59 - last edited 2021-03-17 07:45:24

@josh564 

 

Hello, thanks for your kind feedback, we are sorry this takes long.

 

Update (2020-12-08): 

Our developer has provided a new beta firmware which allows you to manually select the band on the MR6400 v5, please check and confirm:
MR6400(EU) V5: https://static.tp-link.com/2020/202012/20201208/TL-MR6400(EU)v5_1.1.0_0.9.1_[201113-rel63736]_up_boot_all_2020-12-08_09.38.45.zip

 

How to upgrade the firmware? Please check this guide:

https://www.tp-link.com/support/faq/1689/

 

I hope this helps, good day.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#6
Options
Re:Is there any firmware to manually set a specific 4G band (MR6400) V.5
2021-03-16 17:52:22
Hello, I cannot download the firmware link.
  0  
  0  
#7
Options
Re:Is there any firmware to manually set a specific 4G band (MR6400) V.5-Solution
2021-03-17 07:45:53 - last edited 2021-03-17 07:46:05
Recommended Solution
  0  
  0  
#8
Options