How to setup port forwarding?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

How to setup port forwarding?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
How to setup port forwarding?
How to setup port forwarding?
2020-11-12 19:25:25 - last edited 2020-11-18 13:09:14
Model: Deco X60  
Hardware Version: V1
Firmware Version:

How can I setup this port forwarding?

 

 

Thanks in advance

  0      
  0      
#1
Options
1 Accepted Solution
Re:How to setup port forwarding?-Solution
2020-11-18 13:08:40 - last edited 2020-11-18 13:09:14

@ChristianBurger 

Good day.

Please refer to this link to set up the port forwarding:

https://www.tp-link.com/support/faq/1797/

 

and please make sure the Internet IP address on the X60 is a public IP.

Thanks a lot.

Recommended Solution
  0  
  0  
#2
Options
4 Reply
Re:How to setup port forwarding?-Solution
2020-11-18 13:08:40 - last edited 2020-11-18 13:09:14

@ChristianBurger 

Good day.

Please refer to this link to set up the port forwarding:

https://www.tp-link.com/support/faq/1797/

 

and please make sure the Internet IP address on the X60 is a public IP.

Thanks a lot.

Recommended Solution
  0  
  0  
#2
Options
Re:How to setup port forwarding?
2021-03-23 09:36:31

@TP-Link_Deco Silly question maybe but how can you check if the IP addres of the Deco X60 is public?

  0  
  0  
#3
Options
Re:How to setup port forwarding?
2021-03-23 11:50:32 - last edited 2021-03-23 15:39:23

@MLVC 

MLVC wrote

How can you check if the IP addres of the Deco X60 is public?

 

Follow Step 5 of the link https://www.tp-link.com/support/faq/1797/ in your Deco app: "Go back to the Advanced page, tap IPv4 and check the WAN IP address of the Deco system."

Note IP address under WAN section.

 

Open www.whatismyip.com web site from browser on any wired or wireless device connected to Deco mesh. See what IP address web page shows right after "My Public IPv4 is:".

 

If these two IP addresses are the same, you have confirmed that your Main Deco Internet IP address is public IP address.

  0  
  0  
#4
Options
Re:How to setup port forwarding?
2021-05-19 05:18:14

@TP-Link_Deco 

Model: TL-MR6400

Hardware Version: V5

Firmware Version: 1.3.0 0.9.1 v0001.0 Build 201207 Rel.56223n

So i have the tplink mr6400 v5 4g i configured a  windows server 2008 r2 webserver port 80 Internet Information services  & remote desktop connection port 3389 doesnt work over internet external  public ip address then internal private  ipaddress only private ip work single ip address LAN working i cannot access anywhere over internet pubic ip adress

Normally i would access my pc from outside my house with my modem.

Now i wanna setup remote desktop connection and it doesn't work.

I used the right external and internal port for remote desktop (3389) and the ip of the pc i wanted to access.

But when i wanna acces it with my ip form my isp it cant connect to it.

It does work locally when I type the external public  IP address from the tplink mr6400 4g router  currently firmware v5 

If i check it of the port is open, i see its closed on overy ip adress that . https://gyazo.com/d66aec2b7541a238c55c75a9402aa7c3

This is my setup; the tplink mr6400 v5  4g router is connected to my modem and from  tplink mr6400 v5 Ethernet  connected to my windows server 2008 R2

 

 

Please help Me!!!!

  0  
  0  
#5
Options

Information

Helpful: 0

Views: 1527

Replies: 4

Related Articles