Home

Forums

Stories

Knowledge Base

Home Network Community > All Threads > Computer in ISP router net vs rest of devices deco’s net

< All Threads

Computer in ISP router net vs rest of devices deco’s net

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Computer in ISP router net vs rest of devices deco’s net

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

jotemo87

2021-01-03 21:50:09 - last edited 2021-01-04 02:17:13

Posts: 1

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2021-01-03

Computer in ISP router net vs rest of devices deco’s net

2021-01-03 21:50:09 - last edited 2021-01-04 02:17:13

Model: Deco M4

Hardware Version:

Firmware Version:

Hi,

I have a box at the entrance of my house, where the ISP router is located, and five Ethernet cables that go through to the house to the rooms. I have connected two Deco M4: one in room A, another in room B.

When I configured the two Decos, a new wifi network was created. So, I addded all the wireless devices to this new wifi network, like the printer.

The problem comes when I connect my computer located in room C by wire to the ISP router. Therefore, the computer is connected to the ISP router network, and the printer, so all the rest of devices, is connected to the Deco network. So, I cannot connect the printer with the computer wirelessly.

I don't have a clue how to solve this.

Thanks!

1 Accepted Solution

TP-Link

2021-01-04 02:16:54 - last edited 2021-01-04 02:17:13

Posts: 6831

Helpful: 3036

Solutions: 536

Stories: 28

Registered: 2018-07-23

Re:Computer in ISP router net vs rest of devices deco’s net-Solution

2021-01-04 02:16:54 - last edited 2021-01-04 02:17:13

@jotemo87

Hi,

Thanks for your time and patience.

Since Deco M4 is working as a wireless router as well, it would create a new IP range.

Please refer to this link to change M4 as an access point:

https://www.tp-link.com/en/support/faq/1842/

Thank you very much and wait for your reply.

Deco Monthly Recap- Check What's Currently Going on With Deco KidShield Test Recruitment, Share Your Ideas With us! Wi-Fi Schedule Ideas Wanted!

Recommended Solution

Alexandre.

LV6

2021-01-04 12:31:35

Posts: 4021

Helpful: 2333

Solutions: 531

Stories: 0

Registered: 2020-10-22

Re:Computer in ISP router net vs rest of devices deco’s net

2021-01-04 12:31:35

@jotemo87

You have two options to make it work: run Deco mesh in Access Point mode, or attach computer to Main Deco.

1. Run Deco mesh in Access Point mode

If you only need Deco to improve WiFi coverage, you don't need to run it in Router (default) mode. Configure Deco mesh to run in Access Point mode and every device will be on the same network, as a result.

2. Attach computer to Main Deco.

If you already use second port on Main Deco, you'll need to get gigabit switch for ports expansion, 5-8 ports switch can do. They are not expensive, especially 5-port switches. Make sure it is gigabit, because 100Mbps switches are still sold.

Connect switch to second port of Main Deco, connect to switch Ethernet cables from computer and from what was connected to second port of Main Deco before. You now have computer as a member of Deco network, as well as printer. They should see each other now.

jotemo87

2021-01-03 21:50:09 - last edited 2021-01-04 02:17:13

Posts: 1

Helpful: 0

Solutions: 0

Stories: 0

Registered: 2021-01-03

Information

Helpful: 0

Replies: 2

Computer in ISP router net vs rest of devices deco’s net

Computer in ISP router net vs rest of devices deco’s net

Information

Voters 0

Tags