Archer MR600 v2 manual band selection giving error code:89534 no available band

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Archer MR600 v2 manual band selection giving error code:89534 no available band

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
30 Reply
[Solution] Archer MR600 v2 manual band selection giving error code:89534 no available band-Solution
2021-11-09 03:31:42 - last edited 2021-11-18 08:37:13

@StrikerRon 

Hi, As the error code 89534: no available band when you try to manually select the LTE bands on 3G/4G routers, here are useful suggestions shared by our users.


1. If you are using external antennas, such as LPDA and OMNI type, please pay attention to the LTE frequency of the external band since they might be out of the LTE frequency range on 3/4G routers, and please try to select LTE bands under the original antennas.
like #5 Jprathap mentioned here:

 

2. Turn off mobile date under Basic>internet>mobile data or Advanced>network>internet>mobile data; then try to select the LTE bands again.

like #21 mib896 suggested here:


3. If your LTE gateway(like MR150 v2) does not support manual band selection yet, please install the beta firmware on this link:

[Solution] Manual Band Selection for 4G WiFi Routers

 

4. If your issue actually is: Archer MR600 V2 was working before, then after a reboot, it cannot use the 4G network anymore.
Under 4G preferred mode, it only connects to WCDMA which is a 3G network(if the carrier doesn't support 3G anymore, the internet will not work). When trying to change Network Mode to 4G Only and save it, Error Code 1: Internal Error pops up, Besides, when searching 4G band manually, it shows "erro
r code:89534 no available band"

Please refer to the solution on this link:

[Solution] No connection in 4g after reboot

 

While in case your case is related to neither of them, please feel free to start a new thread with more details about your issue!

Thank you very much.

 

Recommended Solution
  0  
  0  
#25
Options
Re:Archer MR600 v2 manual band selection giving error code:89534 no available band
2021-11-09 08:51:54
Hi Tp-link, I manage to make it work after installing the beta. And install again this version back to https://static.tp-link.com/2020/202011/20201117/TL-MR150(EU)v2_1.1.0_0.9.1_[200930-rel56894]_up_boot_all_2020-09-30_15.53.06.zip
  2  
  2  
#26
Options
Re:Archer MR600 v2 manual band selection giving error code:89534 no available band
2021-11-23 13:52:09

@StrikerRon hello ! how did you get a beta firmware please ?

  0  
  0  
#27
Options
Re:Archer MR600 v2 manual band selection giving error code:89534 no available band
2021-11-24 11:39:28

@Ratus915 

Hi, Already sent via private message.

Thank you.

  0  
  0  
#28
Options
Re:Archer MR600 v2 manual band selection giving error code:89534 no available band
2022-05-26 14:23:46

  @Ratus915 

 

this beta work on mr600 ?

  0  
  0  
#29
Options
Re:Archer MR600 v2 manual band selection giving error code:89534 no available band
2022-06-07 03:26:38

  @Ahmed_Sattar 

 

Hi,MR150 beta firmware will not work for MR600, please provide more details about the problem on your MR600, also let us know the hardware and firmware version of your MR600.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#30
Options
Re:Archer MR600 v2 manual band selection giving error code:89534 no available band
2022-10-20 04:41:21

  @Jprathap 

  0  
  0  
#31
Options
Re:Archer MR600 v2 manual band selection giving error code:89534 no available band
2022-10-20 04:43:08

  @Sumitradipakpa 

Tp link Mr 600  update file is not accepting What is the problem 

  0  
  0  
#32
Options
Re:Archer MR600 v2 manual band selection giving error code:89534 no available band
2022-10-24 02:11:09

  @Sumitradipakpa 

 

Hi, are you trying to update firmware version on MR600? and what is the error message?

 

In addition, what is the current hardware and firmware version of your MR600? and which firmware you are trying to update?

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  0  
  0  
#33
Options
[Solution] Archer MR600 v2 manual band selection giving error code:89534 no available band
2023-01-25 06:20:28

  @TP-Link 

One more thing. I still got the error 89534 even after toggling the mobile data off. What finally did the trick, was mobile data off + reboot. After that I was able to select the band.

 

  0  
  0  
#34
Options