MR600 v1 - BETA Firmware 1.1.0 0.9.1 v0001.0 Build 201204 Rel.66940n

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

MR600 v1 - BETA Firmware 1.1.0 0.9.1 v0001.0 Build 201204 Rel.66940n

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
MR600 v1 - BETA Firmware 1.1.0 0.9.1 v0001.0 Build 201204 Rel.66940n
MR600 v1 - BETA Firmware 1.1.0 0.9.1 v0001.0 Build 201204 Rel.66940n
2021-06-01 13:42:21
Model: Archer MR600  
Hardware Version: V1
Firmware Version: 1.1.0 0.9.1 v0001.0 Build 201204 Rel.66940n

@TP-Link 

I have chosen bank 3 & 40, but it always connects to 40 & 40 why? refer to the screen attached. 

earlier a few months back it's used to connect 3 & 40 properly for the same settings only then I will get good up/down speed. 

So now, I able to connect either with 3 (setting band B = empty) and 40 (setting band B=empty) separately. 

whereas 3 & 40 aggregations are not happening, even if aggregation failed, it should connect to only one bank 3 or 40, should not be 40 & 40 as per setting, right?

please refer to the screenshot and suggest. 

 

 

 

 

 

 

Thanks

  1      
  1      
#1
Options
6 Reply
Re: MR600 v1 - BETA Firmware 1.1.0 0.9.1 v0001.0 Build 201204 Rel.66940n
2021-06-04 09:44:21

@Satheskumar 

 

Whether the bands aggregate or not, and how these bands are aggregated with each other, are decided by the cellular tower, the router only sends the request to the cellular tower in your area.

 

Just to confirm, can you get band 3 + band 40 on another 4G router, or can you get the two aggregated on the phone?

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#2
Options
Re: MR600 v1 - BETA Firmware 1.1.0 0.9.1 v0001.0 Build 201204 Rel.66940n
2021-06-04 10:04:46

@Kevin_Z 

 

In this same router a month back I was getting band 3 & 40 aggregation, even I have captured the screenshot and posted in one of the thread for some other issue. 

Not other with any other router or Phone. 

 

 

The only change I have done is updating the BETA firmware and resetting because of some other issues. 

  0  
  0  
#3
Options
Re: MR600 v1 - BETA Firmware 1.1.0 0.9.1 v0001.0 Build 201204 Rel.66940n
2021-06-04 10:10:11

@Kevin_Z 

 

Only my point is how the router is allowing to aggregate 40 & 40-even network force because I have set a rule as 3 & 40.

if aggregation is not happening 3 & 40 may be fine.. but it should aggregate with 40 & 40 when I did not define it. 

 

agree ? but at the end of the day, I wanted aggregation 3 & 40. only then I will get good speed. please help. 

  0  
  0  
#4
Options
Re: MR600 v1 - BETA Firmware 1.1.0 0.9.1 v0001.0 Build 201204 Rel.66940n
2021-06-09 12:26:12

@Satheskumar 

 

We have reported the issue to the support engineers, they will likely reach out to you via email to continue to troubleshoot your issue.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Connect TP-Link Archer BE550 to Germany's DS-Lite (Dual Stack Lite) Internet via WAN Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer AX55V2 Supports WireGuard VPN, EasyMesh Ethernet Backhaul, IoT Network, Speed Limit,and More If you found a post or response helpful, please click Helpful (arrow pointing upward icon). If you are the author of a topic, remember to mark a helpful reply as the "Recommended Solution" (star icon) so that others can benefit from it.
  0  
  0  
#5
Options
Re: MR600 v1 - BETA Firmware 1.1.0 0.9.1 v0001.0 Build 201204 Rel.66940n
2021-06-13 13:48:10

@Kevin_Z 

Just to udpate you, I am still waiting for your support team assistance. 

  0  
  0  
#6
Options
Re: MR600 v1 - BETA Firmware 1.1.0 0.9.1 v0001.0 Build 201204 Rel.66940n
2021-12-06 07:31:00
download firmware BETA Firmware 1.1.0 0.9.1 v0001.0 Build 201204 Rel.66940n tanks
  1  
  1  
#7
Options