Home Network Community > All Threads > Tplink vr600 connect issue
< All Threads

Tplink vr600 connect issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Tplink vr600 connect issue

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Tplink vr600 connect issue
Tplink vr600 connect issue
2021-06-24 12:01:49 - last edited 2021-06-24 12:03:41
Model: Archer VR600  
Hardware Version: V2
Firmware Version:

Hi all 

I have tplink vr600 and I need tp make it as access point 

I put the mode on bridge and disabled dhcp 

Phones are connected without a problem 

But I can't enter the vr600 page  that I put even if I'm using static ip

I put 172.12.1.200 as ip with dhcp disabled 

And I can't reach this ip

  0      
 
  0      
 
#1
Options
9 Reply
Re:Tplink vr600 connect issue
2021-06-30 03:43:15

@Omae1 Hello, 

 

Putting modem on Bridge mode is not necessary when setting up the modem as an Access Point,

It is recommended to factory reset the modem, turn off the DHCP after settings up a static IP for modem, here is a guide: 

https://www.tp-link.com/support/faq/2655/

Deco Monthly Recap- Check What's Currently Going on With Deco KidShield Test Recruitment, Share Your Ideas With us! Wi-Fi Schedule Ideas Wanted!
  0  
  0  
#2
Options
Re:Tplink vr600 connect issue
2021-07-03 11:30:12 - last edited 2021-07-09 08:07:14

@TP-Link the same thing 

Connected no internet 

  0  
  0  
#3
Options
Re:Tplink vr600 connect issue
2021-07-06 08:12:28

@Omae1 

Hi, this time, after turning off the DHCP server, you could log into the VR600 via static IP 172.12.1.200, right?

What is the IP settings on the smartphone when it is connected to the Wi-Fi of VR600？

May I know the model number of your main router?

Deco Monthly Recap- Check What's Currently Going on With Deco KidShield Test Recruitment, Share Your Ideas With us! Wi-Fi Schedule Ideas Wanted!
  0  
  0  
#4
Options
Re:Tplink vr600 connect issue
2021-07-06 11:52:03

@Omae1 

 

It's pointed in the guide, that you should have your VR600 in the same subnet as your main router ? What's the main router IP address ?

Also you've set the VR600:

It is recommended to use 24 bit subnet mask - 255.255.255.0.

 

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#5
Options
Re:Tplink vr600 connect issue
2021-07-09 08:03:31

@TP-Link yes I can go to the login page 

The ip configuration is DHCP not static ip cause the vr600 connected by lan from another router 

The other router is tplink 841 v5 

I tried more than one router but the problem is the same 

  0  
  0  
#6
Options
Re:Tplink vr600 connect issue
2021-07-09 08:06:12

@terziyski it's not the same subnet because vr600 not allowing me to put 255.255.255.0 on this ip

The main router ip is 172.12.1.47

  0  
  0  
#7
Options
Re:Tplink vr600 connect issue
2021-07-09 14:06:53 - last edited 2021-07-12 17:17:29

@Omae1 

 

You have to re-arrange the WR841N LAN settings to be able to put both devices in the same subnet with private IP addresses.

For WR841N LAN settings use (for example) 192.168.1.1 / netmask 255.255.255.0, DHCP range 192.168.1.2-192.168.1.100.

For VR600 LAN settings use Static IP - 192.168.1.101 / netmask 255.255.255.0, DHCP off.

Connect both devices with cable - LAN port to LAN port - that's pretty much the guide that @TP-Link posted.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  0  
  0  
#8
Options
Re:Tplink vr600 connect issue
2021-07-12 09:30:55

@terziyski 

Thanks for explaining 

But I'm not using 192.168.1.. Ip 

I have serial ip from 172.12.1.2 to 172.12.1.200 - I mean that I have more than 2 routers and if I change the vr600 with any other router like tplink v14 or v6 or other company router works fine - 

The problem I have that the tplink 841 v5 netmask is 255.255.255.0

But in vr600 i can't put this netmask 

Do you say if I put the netmask in 841 v5 the same with vr600 will solve the issue? 

  0  
  0  
#9
Options
Re:Tplink vr600 connect issue
2021-07-12 17:16:42 - last edited 2021-07-12 17:30:34

@Omae1 

 

If I understand correctly your main router is WR841N and you want to use the VR600 as an AP connected to WR841N.

If that's correct, then use the following as a reference to configure both devices.

 

For WR841N - your main router.

LAN IP address:

DHCP server:

For VR600 LAN settings:

 

Cable connection between those two devices should be WR841N LAN port to VR600 LAN port.

Note:

If VR600 in in Wireless Router Mode don't use LAN4/WAN port (use LAN1-3)

If VR600 is in DSL Modem Router Mode you can use any LAN port

 

Now, if I didn't understand your setup correctly:

If VR600 is in bridge mode and you use WR841N as a main router that's a normal configuration to avoid the double NAT in your network.

If you want VR600 to be the main router (but not in bridge mode) and want to use the WR841N as an AP then use the following guide - Case 2.

If this was helpful click on the arrow pointing upward to make it blue. If this solves your issue, click the star to make it blue and mark the post as a "Recommended Solution".
  1  
  1  
#10
Options

Information

Helpful: 0

Views: 1739

Replies: 9

Related Articles
Connection issue VR600 too many clients?
1040 0
TPLink VR600 and NowTV broadband
1029 0
Vr600 and deco issue
630 0
TP-Link Archer VR600 V2 latest beta firmware guest network issue
1300 0
Vr600 V3 errors issue
1124 0
VR600 Usb Storage issue
845 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.