TL-WA850RE poor WiFi speed as an Access Point
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hi, I cannot seem to get more than 50Mb/sec out of the TL-WA850RE configured as an access point.
The device is connected to a 1G hub which speedtest on a PC to the same hub gives 200Mb/sec.
The device is on channel 11, my main router (some distance away) is on channel 1.
Is there anything I can do to improve speed for the TL-WA850R as a WAP. Box claims N300 300 Mbps 2.4Ghz
Many thanks.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Leave it to Auto then, let the device determine the appropriate channel width.
By the way the ethernet port of the device is 10/100mbps capable - specs.
That means even if you have it connected to 1000mbps hub port, there still be a bottleneck with theoretical max of 100mbps.
Wireless ethernet is a half-duplex connection, so theoretically you won't get more than 150mbps bandwidth of a 300mbps connection, and then again you're limited to 100mbps by the ethernet port.
Have you observed the wireless connection association speed (PC, phone or whatever you're testing with) when connected to TL-WA850RE ? Are you connecting at 300mbps ?
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Tried that and it slowed down speed by about 8Mbps.
This WAP is in an office where only 2 devices connect to it. Two other nearby routers are on channel 1 and 6.
I have tested with low medium and high power, not any better.
May have to return this as I was expecting better bandwidth.
Nothing much in the log file:
1 INFO 0days, 00:00:00, LAN:Attach mirror0 to stack.
2 INFO 0days, 00:00:00, LAN:Set interface mirror0 ip=192.168.1.130 netmask 255.255.255.0.
3 INFO 0days, 00:00:00, DHCPS: Dhcps start
4 INFO 0days, 00:00:00, HTTPD: Http server start!
5 INFO 0days, 00:00:01, DHCPS: Dhcps stop
- Copy Link
- Report Inappropriate Content
Leave it to Auto then, let the device determine the appropriate channel width.
By the way the ethernet port of the device is 10/100mbps capable - specs.
That means even if you have it connected to 1000mbps hub port, there still be a bottleneck with theoretical max of 100mbps.
Wireless ethernet is a half-duplex connection, so theoretically you won't get more than 150mbps bandwidth of a 300mbps connection, and then again you're limited to 100mbps by the ethernet port.
Have you observed the wireless connection association speed (PC, phone or whatever you're testing with) when connected to TL-WA850RE ? Are you connecting at 300mbps ?
- Copy Link
- Report Inappropriate Content
are you saying the WiFi is limited to 50Mbps when the ethernet is used as source for the device due to the 100Mbps port ? If so how is the N300 achieved ?
- Copy Link
- Report Inappropriate Content
No. You've misinterpreted what I was trying to explain. You're limited to 100mbps when the ethernet port is used - AP mode.
As for the N300 it could be achieved when using the device in range extender mode - wirelessly, and again N300 means no more than 150mbps bandwidth, because of the half-duplex technology.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Sorry for relay. N300 is the Wireless Link speed between RE and wireless client :
https://www.tp-link.com/support/faq/2265/
In your case, actual speed is capped by Ethernet port, and also speed get reduced when signal being transmitted in the Air.
If your Bandwidth is more than 100Mbps, you could consider RE/AP with a Gigabit port to extend Internet. A dual-band RE/ AP should have a better performance if devices supports 5Ghz.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
Information
Helpful: 0
Views: 2473
Replies: 8
Voters 0
No one has voted for it yet.