Official Release Deco X50/X55 V1/V1.2/V2 with VPN/Static Route/MTU
This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Hello Everyone,
We are excited to announce the official firmware version 1.2.x for Deco X50/Deco X55 V1/V1.2/V2 has been released recently. With this new firmware, you can now configure the VPN server/client, and other advanced features on the Deco.
Deco X50_V1/V1.2/V2
Deco X55_V1/V1.2/V2
>>How to update the firmware via web UI
Release Note:
New features:
1. Support for VPN server features, including Open VPN, PPTP VPN and L2TP/IPsec VPN.
2. Support for VPN client features, including Open VPN, PPTP VPN and L2TP/IPsec VPN.
3. Support for Static Route under Deco APP>More>Advanced.
4. Added the ability to customize the MTU size under Deco APP>More>Internet Connection>Internet Connection Type.
5. Added IOT network function.
* The following features(6-12) are also supported on 1.1.0 version:
6. Added Reboot Schedule for every day/week under Deco App > More > Reboot Schedule.
7. Added support for customizing Satellite Deco Signal Source under Deco App > Internet > Select the Satellite Deco > Signal Source.
8. Added support for customizing clients Connection Preference under Deco App > CLIENTS > Select the client > Click the gear icon on the right-up corner > Connection Preference.
9. Added No-IP and DynDNS to the DDNS settings under Deco App > More > Advanced > DDNS.
10. Added Smart DHCP on/off switch in Access Point mode under Deco App > More > Advanced > Smart DHCP.
11. Added a prompt notification when the Ethernet link rate goes down to 100Mbps.
12. Added schedule and bandwidth limit to guest network under Deco App > More > Wi-Fi > Guest Network.
Improvements:
1. Optimized the MAC Clone function.
2. Improved system reliability and security.
Note:
1. The Advanced features need to be configured on the Deco APP and please make sure your Deco APP is up to date.
2. Some new features would not be available when the router is working in Access Point mode.
3. The firmware downgrade needs to be performed by firmware recovery. >>How to use firmware recovery on Deco
Please feel free to comment below if there is any question about the new firmware.
- Copy Link
- Subscribe
- Bookmark
- Report Inappropriate Content
Hi, the MTU could also be customized under the PPPOE connection.
For other modes, you could refer to this link:
https://community.tp-link.com/en/home/forum/topic/582238?replyId=1133728
Best regards.
Thrill, Hi, if you bought it online, it might be hard to know the hardware version in advance. But if you bought it in the local stores, the hardware version will be printed on the box, such as:
- Copy Link
- Report Inappropriate Content
@David-TP Do you know if the Deco x50-DSL will have MTU configuration? It releases tomorrow in UK.
- Copy Link
- Report Inappropriate Content
in the First post it says that the latest build is from 20230118 , but when pressed it downloads an older build current 1.2.0_221122. Is this a link error?
- Copy Link
- Report Inappropriate Content
Hello @David-TP
I can see a couple of questions on the x50 4G but couldn't find the answer.
Can I use this update on my 4G version? If not when will the X50 4G get the ability to add a static router please?
Thanks
Dan
- Copy Link
- Report Inappropriate Content
@David-TP
Yesterday I tried this new pre-release firmware and I want to test the WAN/WLAN auto-sensing port; I read that you post it that if the Ethernet cable is not unplugged it will not start auto-sensing by looking other ports.
If I unplug the WAN Ethernet cable from the Deco it makes my network devices connected through Ethernet or switch/Ethernet to be offline from the internal network.
Options:
1. Removing the Ethernet cable from the modem side, but still connected to the Deco?
2. Shut down the modem and Ethernet cable plugged in both side?
I want to simulate a test when Modem gets issue and makes no internet, to check that other devices are still connected to the network by Ethernet cable.
- Copy Link
- Report Inappropriate Content
@David-TP Hi David,
I have 2 X50 and am I upgrade both X50 using wire or upgrade one and the other will automatically upgraded from the first unit?
Thanks in advance for the answer
Art.
- Copy Link
- Report Inappropriate Content
@Kransky.dan Hi, welcome to the community. This firmware could not be used on Deco X50-4G. the same firmware is planned to be released for X50-4G as well but the ETA is not guaranteed.
ezeb, Thank you for your question.
There is some information for your reference about the WAN/WLAN auto-sensing port:
Options:
1. Removing the Ethernet cable from the modem side, but still connected to the Deco?
The wan port would not be changed.
2. Shut down the modem and Ethernet cable plugged in both side?
It will trigger WAN/WLAN auto-sensing and both ports on Deco are left idle as WAN ports.
tguy888, Hi, normally if you update the main Deco X50 via web UI, the satellite Deco X50(please make sure it is on V1 as well) would get updated as well.
Best regards.
- Copy Link
- Report Inappropriate Content
- Copy Link
- Report Inappropriate Content
HI @David-TP
What is the different on this two version
1.2.0 20221122 Rel. 46653
vs
Deco X50-V1-1.2.0 release date 20230131
because the 20221122 was last week in this post, and this week you edited the Post with 20230131.
it was a bad typo in the file name from the original post, or there was an update on the 1.2.0 pre-release firmware?
- Copy Link
- Report Inappropriate Content
Hi, 1.2.0 build 20230113(released on 2023.1.31) is an updated version of 1.2.0 build 20221122 Rel. 46653.
I emphasized the release date so that users could be able to see there is a newer version.
Best regards.
- Copy Link
- Report Inappropriate Content
Information
Helpful: 5
Views: 35930
Replies: 175
Voters 5
