Use LAN ports when in Access Point Mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Use LAN ports when in Access Point Mode

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Use LAN ports when in Access Point Mode
Use LAN ports when in Access Point Mode
2023-09-12 12:36:56 - last edited 2023-09-13 09:30:36
Model: Archer C64  
Hardware Version: V1
Firmware Version:

I am considering buying a TP-Link Archer C64 v1 router.

Two questions:

1) I note that the power adapter can deliver max. 12 W and presumably does not draw much more than than from mains;

but what is the actual power consumption under normal use?

2) I want to use it in access point mode.

I read that after selecting access point mode I should connect the C64's WAN port to the wired network.

So far, so good. Now comes the question:

Will the built-in network switch still work?

In other words: Can I use the 4 LAN ports to extend my wired network?

Thanks for any insights!

 

  0      
  0      
#1
Options
2 Accepted Solutions
Re:Use LAN ports when in Access Point Mode -Solution
2023-09-12 14:57:35 - last edited 2023-09-13 09:31:57

  @KrKj 

 

The C64 power consumption will depend on C64 configuration and usage - maximum is 12W. Usually it consumes less than that.

Yes when in AP mode, all of its LAN ports are available for client devices.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
Recommended Solution
  6  
  6  
#2
Options
Re:Use LAN ports when in Access Point Mode -Solution
2023-09-12 18:50:04 - last edited 2023-09-13 09:30:58

 

With one wired client and two wireless clients connected the power consumption of my C64 is around 4.0 W. The peak power recorded over a period of half an hour was 5.5 W.

 

 

Recommended Solution
  5  
  5  
#5
Options
5 Reply
Re:Use LAN ports when in Access Point Mode -Solution
2023-09-12 14:57:35 - last edited 2023-09-13 09:31:57

  @KrKj 

 

The C64 power consumption will depend on C64 configuration and usage - maximum is 12W. Usually it consumes less than that.

Yes when in AP mode, all of its LAN ports are available for client devices.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
Recommended Solution
  6  
  6  
#2
Options
Re:Use LAN ports when in Access Point Mode
2023-09-12 17:11:53

  @terziyski 

Many thanks.

Say, with no USB devices, 2 idle wifi clients and 2 idle wired clients, are we looking at 1W, 2W, 4W, 6W, 8W, 10W or 11W?

  0  
  0  
#3
Options
Re:Use LAN ports when in Access Point Mode
2023-09-12 17:47:55 - last edited 2023-09-12 18:35:27

  @KrKj 

 

I can make an educated guess only, cause I didn't use a power meter to capture C64 consumption, but I would assume between 4W-10W.

C64 doesn't have an USB port anyway.

If this was helpful click once on the arrow pointing upward. If this solves your issue, click once the star to mark it as a "Recommended Solution".
  3  
  3  
#4
Options
Re:Use LAN ports when in Access Point Mode -Solution
2023-09-12 18:50:04 - last edited 2023-09-13 09:30:58

 

With one wired client and two wireless clients connected the power consumption of my C64 is around 4.0 W. The peak power recorded over a period of half an hour was 5.5 W.

 

 

Recommended Solution
  5  
  5  
#5
Options
Re:Use LAN ports when in Access Point Mode
2023-09-13 09:58:09

@terziyski

@woozle
Many thanks, both!

  0  
  0  
#6
Options

Information

Helpful: 0

Views: 4304

Replies: 5

Related Articles