@Basboi85 

 

Changed over the ethernet cable that i suspected had broke down on the mancave satellite is now back to 1000mbps full duplex 

 

 

Still getting the network crash.

 

as soon as I plugged in the ethernet to main router. 

 

Had to reboot the main router twice before it would let me connect back to it on WiFi even though it was showing my wifi is active. 

 

 

 

 

 

 

  @Basboi85 

 

And again it's crashed 🤬🤬🤬🤬

 

 

 

 

 

Says I have wifi but won't let me connect

 

It started self reboot  1st 3 lights was on then all lights went out but power light kept flashing then router then all lights went out for 2 mins now powered on and seems tp be running as normal 

 

  @Sunshine 

 

Hi sunshine thanks for getting back to me. 

 

 

They are all connected via ethernet 

 

 

 

 

 

Lan 4 is my man cave Ax72,

 

And my top floor Ax72 is on the top floor of my 2 storey house, my  Ax72 on the top floor is on either lan 1 or 2 but it does have a tp link 24port gb unmanaged switch between it. 

 

 

My network layout goes as 

 

Main Ax72

 

lan cable on lan 1 to a tp link 24 port GB unmanaged switch (  TL-SG1024D) then I have about 12 ports populated off that. 

 

Lan cable on lan 2 also goes to another tp link 24 port gb unmanaged switch ( TL-SG1024D) and then has about 16 ports populated 

 

 

The top floor AX72 has no devices connected to the lan ports it just emits wifi for my top floor as i have a 2 story house as the very back room suffers from wifi even though the ax72 emits a very high range there is about 5 solid walls between the router and that room gets really low signal understandably. 

 

 

Lan 3 nothing connected 

 

Lan 4 has a outdoor rated 25M ethernet that runs to the bottom of my garden into my outbuilding to my ax72 then all I have connected to mancave ax72 is a tp link outdoor cctv camera via ethernet, a wifi plug to control lights and a alexa puck via wifi 

 

 

I chose to split the lan connections via 2 switches to help with load balancing also if one of the 2 switches was to break/go down I could switch over a few ports to keep the ports that was needed Up and running until I replaced the switch.  

 

Please note that even though the switches have populated ports they all aren't being used. 

 

Each bedroom has a 4 port lan socket 

 

bedroom 1 has 3/4 ports being used 

bedroom 2 has 0/4 ports being used 

Bedroom 3 has 2/4 ports being used 

Bedroom 4 has 2/4 ports being used

 

And my living room has a 6 port socket that only has 3/6 that are being used. 

 

I couldn't even pin point why most of the time it has crashed it just kicks everyone off wifi and lan connections stop Even though all lights are on the main unit and when you search for the wifi it shows its there but as shown in pic in above post it refuses to allow you to connect. 

 

However I have noticed strangley that some devices that are connected via lan or wifi will work and then eventually stop all together This can be either a tp link wifi camera or my alexa cube connected via lan. 

 

 

It has crashed during the day and also in the evening Whether all my kids are at school or at home. 

 

Ive recently changed my mancave cable as i think that had broken down (gone from gb full duplex to 100mb full duplex)  and when i connected that to the main unit that had made it crash aswell 

 

Im having major issues still with my tether app forgetting settings so i re input the settings again  it then forgets it even though it says success and that makes it crash. 

 

I have made other posts about this issue. 

 

https://community.tp-link.com/en/home/forum/topic/655838

 

https://community.tp-link.com/en/home/forum/topic/650280?replyId=1312126

 

 

I then have to turn the main unit off for 10-15 seconds then reboot the main unit. 

 

 

I hate to tempt fate but for the last 3-4 days it hasn't crashed that I'm aware of. 

 

I did have a power cut a few days ago and the power was off for just over a hour and since then it's not happened but then I haven't touched anything and just left it completely alone as it has been working. 

 

I do need to change my wifi channel as for some reason my main unit has decided to change channels and now my wifi speeds have dropped but that means I have to go into the settings but I'm pretty sure it will then in turn crash the unit. 

  @Sunshine 

 

Hi sunshine, 

 

 

 

Many thanks for your help in this matter, 

 

Really appreciate it 👍🏻

Did the team reached out to you or it was just a fake promise

  @Sagar0077 

 

Hi I did get a reach out eventually, I got sent the latest update before it was released. 

 

It seemed to have stopped the random crashing but still i suffer with the crashing if I try and change settings via tether app. 

 

 

Tried changing wifi channel from 44 as its getting alot of interference/heavily congested and it kept refusing to change channels, kept saying failed, after the 3rd attempt it went through the usual sequence. 

 

Kicked everything off via wifi and ethernet, 

 

Then had to reboot all 3 of my ax72's One by one for all to be happy again and not tried since as its apparent the issues are still there. 

 

 

I've noticed aswell if I want to load my family profiles it takes a good minute to load to the first part of the profiles page before it shows my actual profiles, 

 

It takes about a extra 30 seconds on top for it to load and show me the actual profiles. 

 

Not sure what has happened in the last couple  updates bit everything has seemed to have slowed right down when it comes to loading info via the tether app. 

 

Took 38.11 seconds to load this then 

Took  48.6 seconds to get here, 

 

This is pretty quick to what I have been getting. 

 

Not sure if this is the same for everyone but it used to be alot faster than this a few updates back tp where it wouldve fully loaded showing the profiles within I'd say 20 seconds

  @Basboi85