TP-LINK ARCHER AXE75 (AXE5400 Tri-Band Gigabit Wi-Fi 6E Router)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

TP-LINK ARCHER AXE75 (AXE5400 Tri-Band Gigabit Wi-Fi 6E Router)

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
TP-LINK ARCHER AXE75 (AXE5400 Tri-Band Gigabit Wi-Fi 6E Router)
TP-LINK ARCHER AXE75 (AXE5400 Tri-Band Gigabit Wi-Fi 6E Router)
2024-03-23 01:42:09 - last edited 2024-04-08 09:13:31
Model: Archer AXE75  
Hardware Version:
Firmware Version:

Does Archer AXE75 support Bridge mode? From the marketing info I see only:

 

  • Router Mode
  • AP Mode

 

Entering the tplink emulator for Archer AXE75 I see same under CHANGE MODE

 

Following this tutorial https://www.youtube-nocookie.com/embed/CbN1apeTbLI I cant see any Bridge mode

 

But under Network > Internet > NAT I see Enable/Disable NAT and also I see some option called NAT Forwarding... is this the compensation for not having the Bridge Mode or did I miss something? 

 

My setup: ISP Modem > cat6e > Archer AXE75 > cat6e > Archer AXE75 ...so obviously I would like to connect it in Bridge mode to avoid triple NAT and other rising issues

  0      
  0      
#1
Options
1 Accepted Solution
Re:TP-LINK ARCHER AXE75 (AXE5400 Tri-Band Gigabit Wi-Fi 6E Router)-Solution
2024-03-25 09:13:17 - last edited 2024-04-08 09:13:31

  @hWmMzIfYNRISEgn 

 

Hi, by bridge mode, you just would like to not use NAT, it will still connect to your network via Ethernet cable, right? If so, you should use the AP mode, which is not a NAT any more.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
3 Reply
Re:TP-LINK ARCHER AXE75 (AXE5400 Tri-Band Gigabit Wi-Fi 6E Router)-Solution
2024-03-25 09:13:17 - last edited 2024-04-08 09:13:31

  @hWmMzIfYNRISEgn 

 

Hi, by bridge mode, you just would like to not use NAT, it will still connect to your network via Ethernet cable, right? If so, you should use the AP mode, which is not a NAT any more.

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
Recommended Solution
  0  
  0  
#2
Options
Re:TP-LINK ARCHER AXE75 (AXE5400 Tri-Band Gigabit Wi-Fi 6E Router)
2024-04-22 16:12:42

  @Sunshine in case of this topology:

ISPmodem > ArcherAxe75(router1 - router mode) > ArcherAxe75(router2 - AP mode)
 

  1. should router1 > router2 be connected via LAN > LAN or LAN > WAN port?
  2. should the DHCP server on router2 be set to AUTO or OFF?
  3. should NAT be ON or OFF on router2?
  4. if router1 broadcasts wifi, will router2 (upstairs) be able to cover the upper floor from the wifi broadcasted from router1?
  5. should router2's wifi be turned off so that router1's wifi covers (via router2) the whole house?
  6. or should router2's wifi be turned on as well? and in that case should the SSID and PW be the same or different from the wifi from router1?


note: I don't need to have 2 wifi networks if it's not necessary.

simply put, the idea is as follows: I'm connected to wifi from router1 on the ground floor and I run upstairs and don't lose the signal

note 2: wifi from router 1 cannot cover the upper floor, that's why I bought two identical routers to cover the whole house

please advise me, I'm no IT person and I've been playing with it for 3 days and it still doesn't work.

  0  
  0  
#3
Options
Re:TP-LINK ARCHER AXE75 (AXE5400 Tri-Band Gigabit Wi-Fi 6E Router)
2024-04-23 02:52:26

  @hWmMzIfYNRISEgn 

 

Hi, you could refer to Case One in this guide to configure the second Archer AXE75 as an access point: How to configure the TP-Link wireless router as Access Point

Regarding your questions:

1. LAN > WAN

2. DHCP Server on router 2 can be either Auto or OFF, when it is Auto, if it connects and detects the DHCP Server of Router 1, it will turn off its own DHCP Server.

3. No NAT any more when router 2 is in AP mode

4. Router 1 and Router 2 are different WiFi signals no matter the WiFi settings are the same or not, they are connected via wired cable instead of WiFi.

5/6. It depends on whether the Router 1 WiFi could cover the whole house or not, if not, you could turn WiFi on on the Router 2 as well. When Router 2 WiFi is turned on, you could use the same WiFi name&password as the Router 1 since you don't need two WiFi networks. 

Nice to Meet You in Our TP-Link Community. Check Out the Latest Posts: Archer GE550 - BE9300 Tri-Band Wi-Fi 7 Gaming Router EasyMesh Is Available When Wi-Fi Routers Work in AP Mode as A Controller. Archer BE550 New Software Enhances System Stability and Optimizes MLO Network Stability. TL-WA3001 Supports EasyMesh, Speed Limit, Guest Network in AP Mode and/or Multi-SSID Mode. If you found the post or response helpful, please click Helpful. If an answer solves your problem, click "Recommended Solution" so that others can benefit from it.
  1  
  1  
#4
Options