Home Network Community > All Threads > Wired mesh
< All Threads

Wired mesh

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

Wired mesh

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Wired mesh
Wired mesh
2024-04-27 18:13:46
Tags: #Deco Ethernet Backhaul #Access Point Mode
Model: Deco X55  
Hardware Version:
Firmware Version:

Dear,

 

I need some help since i am not able to test it right now. 
 

i want to setup network like this

 

MAIN ROUTER (Archer AX53) to Switch (TP-Link TL-SG108E) and then from switch to 3 deco x55 units ( all of them wired to switch since i have cables inside the walls alredy) 


main concerns are :

will i get 3 networks ? (One per each deco) 

Is it possible to make it as one network/mesh in this scenario where deco units are wired to switch so i assume they can only be AP? 
 

i read something about ethernet backhaul but im not sure if that is whats happening in my situation and actually i didnt understand it very well.

 

also i was wondering if i buy another deco units that supports "easymesh" technologie it will be piece of cake to make archer + 3 decos just as one mesh network? Just set archer as main router and 3 deco units as satellites i guess...

 

  0      
 
  0      
 
#1
Options
5 Reply
Re:Wired mesh
2024-04-29 07:59:41

  @marmardes 

Hi, welcome to the community.

With the following topology:

Internet----Archer AX53---TL-SG108E---3*Deco X55s(in AP mode)

 

You will have two WiFi networks, one from AX53, and the other from Deco X55. All three Deco X55s in AP mode will still establish a unit Deco Mesh system.

So usually, it is suggested to turn off the Wi-Fi on AX53 and also use the Deco Mesh WiFi.

Thank you very much and best regards.

 

Check What's Currently Going on With Deco Deco Early Access Firmware Open for Test! Deco APP 3.8.102/3.8.112-Ready for A New Deco Onboarding Experience! Try to leave a Message if urgent help is required.
  0  
  0  
#2
Options
Re:Wired mesh
2024-04-29 08:28:35

  @David-TP 

 

thank you,

 

In case i want to keep network from archer is there any additional settings i can change to prevent any possible troubles/issues? 
 

Thank you!

  0  
  0  
#3
Options
Re:Wired mesh
2024-04-29 09:09:15

  @marmardes 

Hi, you can keep the Wi-Fi of AX53. It would be better to name their SSIDs differently.

So far, the EasyMesh router couldn't establish a united Mesh network with Deco.

Can Deco Mesh, OneMesh, EasyMesh and Omada Mesh products work together?

Thank you very much and best regards.

Check What's Currently Going on With Deco Deco Early Access Firmware Open for Test! Deco APP 3.8.102/3.8.112-Ready for A New Deco Onboarding Experience! Try to leave a Message if urgent help is required.
  0  
  0  
#4
Options
Re:Wired mesh
2024-04-29 15:15:16

  @David-TP 

 

thanks.

 

now i am having troubles setting 3 deco units in AP mode. 
 

any detailed instructions on how to do it via switch which is connected to archer.

 

thanks a lot!

  0  
  0  
#5
Options
Re:Wired mesh
2024-04-30 00:57:01

  @marmardes 

Hi, may I know the model number of the switch?

You can refer to the following instructions here:

General questions about Ethernet Backhaul feature on your Deco

Best regards.

 

Check What's Currently Going on With Deco Deco Early Access Firmware Open for Test! Deco APP 3.8.102/3.8.112-Ready for A New Deco Onboarding Experience! Try to leave a Message if urgent help is required.
  0  
  0  
#6
Options

Information

Helpful: 0

Views: 459

Replies: 5

Tags

Deco Ethernet Backhaul Access Point Mode
Related Articles
Two or more wired units in mesh system
510 0
Deco mesh and wired devices.
450 0
Archer AX10 as wired mesh repeater
3907 2
X20 mesh network AP from R605
489 0
How to force wired backhaul
741 0
Wired backaul
292 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.