Archer c1200 set up as access point, cannot search for update, or update network time

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
12

Archer c1200 set up as access point, cannot search for update, or update network time

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
Archer c1200 set up as access point, cannot search for update, or update network time
Archer c1200 set up as access point, cannot search for update, or update network time
2017-03-24 10:11:19
Model :

Hardware Version :

Firmware Version :

ISP :

I have searched for a while to find something, but cannot. I have an archer c50 set up the same way as i have this one set up, and It retrieves network time from my main router's address. However, the c1200 will not connect. I made sure that i had set the spi firewall to off. I played around with other settings. i'm just not sure what to do. I found some things on another site about setting a static route, but I couldn't get anything to work correctly. Thank you for any help you may be able to give. I searched the forum, and did not find anything like this. I hope this is not a duplicate thread.
  0      
  0      
#1
Options
20 Reply
Re:Archer c1200 set up as access point, cannot search for update, or update network time
2017-03-24 11:49:32
The router checks the updates through the WAN connection.
When you setup the router as an access point, the router itself acts just as a pure switch.
You can setup a static route on the router to get network time updated.
  0  
  0  
#2
Options
Instructions
2017-03-25 04:15:19
Can you point to help on how to enter in the routing for the time servers?
Is there a way to do the same thing with the updates?

tplink wrote

The router checks the updates through the WAN connection.
When you setup the router as an access point, the router itself acts just as a pure switch.
You can setup a static route on the router to get network time updated.
  0  
  0  
#3
Options
Re:Archer c1200 set up as access point, cannot search for update, or update network time
2017-03-25 14:50:39
Please refer to the FAQ link below:
http://www.tp-link.com/en/faq-560.html
  0  
  0  
#4
Options
Re:Archer c1200 set up as access point, cannot search for update, or update network time
2017-10-06 20:11:57
tplink, lol what?! impossible to set default route, not for lan(this is a typical configuration for AP), not for wan: "The address cannot be 0.0.0.0"- for ipv4, "Invalid format"- for ipv6 "::"
just a piece of chinese shit
  0  
  0  
#5
Options
Re:Archer c1200 set up as access point, cannot search for update, or update network time
2017-10-09 17:41:01
what's your model and hardware/firmware? You may send a screenshot for further help
  0  
  0  
#6
Options
Re:Archer c1200 set up as access point, cannot search for update, or update network time
2017-10-10 08:54:16





OMG! he does not even know my model.. look at the title of the topic!! hardware v1
  0  
  0  
#7
Options
Re:Archer c1200 set up as access point, cannot search for update, or update network time
2017-10-11 15:41:42
Sorry for asking the model as you are't the original poster and I just want to make sure. Did you also use the C1200 as AP? Why do you need to set up static routing. Sorry to tell you that 0.0.0.0 is not a valid option to type in
  0  
  0  
#8
Options
Re:Archer c1200 set up as access point, cannot search for update, or update network time
2017-10-11 17:18:26
thx captain obvious, you saved my life! mb u tell me ip address of update server? all ip addresses for correctly obtain the update
  0  
  0  
#9
Options
Re:Archer c1200 set up as access point, cannot search for update, or update network time
2017-10-12 17:59:27
I don't think you can do that, it doesn't look like it's designed that way
  0  
  0  
#10
Options
Re:Archer c1200 set up as access point, cannot search for update, or update network time
2017-10-12 20:13:42
nothing impossible in theory. do you think tp-link's guy does not know anything? i think the same ;) but let's give him a chance.in ipv4 my gateway server is 192.168.85.1, c1200 in AP role is 192.168.85.2.
we have a problem with dns(fig.1)- we can not use gateway's dns, because he in a local network(yes, i know, it is a fucking chinese joke). we will use google's 8.8.8.8(fig.2). how we have a problem with route to 8.8.8.8, fix it with static route(fig.3) and test(fig.4). now we check dns- does work(fig.5).
it remains only to find all the necessary addresses for firmware updates and set routes for them, useless guy from tp-link help us here. yes, we can do without his help, but let's give him a chance to work out their own bread










  0  
  0  
#11
Options

Information

Helpful: 0

Views: 2909

Replies: 20