Home Network Community > All Threads > No IP on Archer C7 setup as Wifi Access Points?
< All Threads

No IP on Archer C7 setup as Wifi Access Points?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

No IP on Archer C7 setup as Wifi Access Points?

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
No IP on Archer C7 setup as Wifi Access Points?
No IP on Archer C7 setup as Wifi Access Points?
2017-12-10 00:41:17
Model : Archer C7

Hardware Version : Archer C7 v2 00000000

Firmware Version : 3.15.2 Build 170525 Rel.37571n

ISP :

Current setup is
Modem: Arris Surfboard 6141
Router: Archer C7, DHCP on / NAT on
This router connects to three access points (LAN port to LAN port) across my house via cat 5e cabling.
* AP #1: Archer C7, DHCP off / NAT off. I am getting ~200mb down / ~10mb up when I plug in directly to LAN port * AP #2: Archer C7, DHCP off / NAT off. I am getting ~200mb down / ~10mb up when I plug in directly
* AP #3: Archer C7, DHCP off / NAT off. I am getting ~40-50mb down / ~6-8mb up when I plug in directly [Not sure why this one is so much slower]
The main issue is terrible wifi performance.
All three APs have the same SSID name but have wifi set to different channels. However for all three I am getting terrible wifi performance. If I can connect at all, the connection is slow (~10-20mb down). Often my macbook or iphone will fail to connect to the internet at all -- "No IP Address" or "No Internet Connection" errors -- over wifi.
When connected on wifi to the router, I get ~200mb down....the wifi there works fine.
Any idea what is causing this issue?
Any and all help appreciated!
  0      
 
  0      
 
#1
Options
4 Reply
Re:No IP on Archer C7 setup as Wifi Access Points?
2017-12-11 03:11:39
Depending on the hardware versions there is a beta firmware for version 2 here

http://forum.tp-link.com/showthread.php?94180-Archer-C7-router-crashed-by-Dell-laptop-with-Killer-adapter&p=195886#post195886

Are you bridging a Port on the Modem ? my Actiontec allows me to bridge Port 1 , so I can have the C7 do DHCP, nat etc. If it's not Bridged you may have a double nat issue?
  0  
  0  
#2
Options
Re:No IP on Archer C7 setup as Wifi Access Points?
2017-12-14 05:57:54
I updated the post with my hardware version.

I don't believe the Surfboard6141 acts as a router (or does NAT). Also it's strange that this connectivity/throughput is limited to wireless connections.
  0  
  0  
#3
Options
Re:No IP on Archer C7 setup as Wifi Access Points?
2017-12-15 02:13:24
So you have 4 C7's ? You aren't using the Wan Port on the 3 APs are you? .......shouldn't be... just the 1st C7 off the Cable Modem ,

http://www.tp-link.com/ca/faq-608.html
Also I believe they should ALL be on the same SSID and Channel and password , so you can wander from room to room and have it seamlessly reconnect if needed to a stronger signal.

Never had that modem but it appears to be a dumbed down Modem that Cable providers don't want anyone playing with as there appears to be virtually nothing to configure looking at the manual....I am surprised there is only 1 Eth.Port though.

http://arris.force.com/consumers/articles/General_FAQs/SB6141-Troubleshooting-Internet-Connection
http://arris.force.com/consumers/articles/General_FAQs/Windows-TCP-IP-Configuration-for-ARRIS-Motorola-Cable-Modems


V2 C7 has a beta firmware out , you could try it..... I am using it and find it better than 16 series Firmwares' if you have one of the effected laptops mentioned in the thread below , with a Killer NIC/WIFI it maybe causing the drop out issue...

http://forum.tp-link.com/showthread.php?94180-Archer-C7-router-crashed-by-Dell-laptop-with-Killer-adapter&p=195886&viewfull=1#post195886



  0  
  0  
#4
Options
Re:No IP on Archer C7 setup as Wifi Access Points?
2017-12-15 05:30:00
Yes, I have 4 C7s.

They all have the same SSID / password. I set the channel to be different to avoid interference. I'm not sure this matters anyway...the default setting is to auto-select?

Perhaps I will try the beta firmware since my issues will not go away but I don't use a Dell.
  0  
  0  
#5
Options

Information

Helpful: 0

Views: 1557

Replies: 4

Related Articles
Archer c7 setup
644 0
Wifi 6, and EAP610 access points
1149 0
AX11000 and access points
646 0
Archer c7 v4 can't access modem IP offline
762 0
Archer C7 AC1750 - Wireless Access Point?
1079 0
AX11000 router with EAP660 HP Access Points
1103 0
About Us
Press
Copyright © TP-Link Systems Inc. All rights reserved.