WDS Bridging Function on AC1750

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.

WDS Bridging Function on AC1750

This thread has been locked for further replies. You can start a new thread to share your ideas or ask questions.
WDS Bridging Function on AC1750
WDS Bridging Function on AC1750
2020-04-10 22:51:04 - last edited 2024-07-11 21:00:26
Model: AC50  
Hardware Version: V7
Firmware Version:

The root router on my system is an AT&T Model 5268AC with the following address

 

Router/Gateway Address: 192.168.1.254

Subnet Mask: 255.255.255.0

 

What IP Address should I enter during the AC1750 Wireless Dual Band Gigabit Rouiter Archer C7/A7 WDS Bridging process?

 

The samples in the user guide on pages 105 and 106 don't make sense.

  0      
  0      
#1
Options
6 Reply
Re:WDS Bridging Function on AC1750
2020-04-10 23:36:56

@CowboyWM 

 

you shouldn't need an IP address.  Log into the router.  Go to Advanced > System Tools> System Parameters and choose which band you want to do WDS with.  You can do both but just one a time.  

 

Say you choose 2.4 GHz.  click on the survey button.  Then click on choose next your host network.  type in the password for that network and click save.  Do the same for the 5GHz and you will complete the WDS process.  Keep in mind WDS is essentially turning a router into a range extender.

  0  
  0  
#2
Options
Re:WDS Bridging Function on AC1750
2020-04-11 03:47:26

@Carl 

 

Carl, thanks for the info but I cannot select the 5G WDS option if the 2G is selected and saved.

 

Step 1 of the manual's instructions say

1 & 2) Go to Advanced > Network > LAN, confirgure the IP address of the extended router to be in the same subnet with the root router, then click Save.

Step 3 says

3) What you described.

Step 4 says

4) Disable DHCP.

 

  0  
  0  
#3
Options
Re:WDS Bridging Function on AC1750
2020-04-13 18:21:43 - last edited 2024-07-11 21:00:22

@CowboyWM 

 

 

Yeah I just confired with some collegues who have used the service before.  They confrimed only one band can be configured. DHCP does need to be truned off as well.  I was under the impression this was automatic but I have since been corrected.  Sorry about the confusion. 

  0  
  0  
#4
Options
Re:WDS Bridging Function on AC1750
2020-04-13 20:58:46

@CowboyWM 

 

Carl, this brings me make to the original question.

 

The root router on my system is an AT&T Model 5268AC with the following address

 

Router/Gateway Address: 192.168.1.254

Subnet Mask: 255.255.255.0

 

What IP Address should I enter during the AC1750 Wireless Dual Band Gigabit Rouiter Archer C7/A7 WDS Bridging process?

  0  
  0  
#5
Options
Re:WDS Bridging Function on AC1750
2020-10-01 06:33:08

@CowboyWM  I got this to work by manually entering a LAN IP address on the same subnet as root router. Or you can make a DHCP address reservation by the MAC id of the LAN port. In your example, it would be `192.168.1.x` where x is unused and outside the DHCP address zone. try `192.168.1.253`

  0  
  0  
#6
Options
Re:WDS Bridging Function on AC1750
2020-12-27 00:13:10

Actually, I am having more or less the same issue.

 

I want to use the AC1750 as a repeater for a Mikrotik hap ac2 router. (192.168.89.1 gateway). I changed to LAN IP to be within the same subnet as the Mikrotik (192.168.89.2 for instance), then I selected the WDS for each band (2.4 and 5 Ghz), added the same password as the host router and in the end I switched the DHCP off on the AC1750. The moment I switched the DHCP off on the AC1750 and plugged in the cable from the Mikrotik main router to the AC1750 WAN, the entire network went down along with the internet connection - not to mention that the AC1750 could no longer be reached. I repeated all the steps according to the instructions (I even tried connecting the cable to any of the other ports than the WAN) and the result is the same. Where is the mistake? Am I missing something?

  1  
  1  
#7
Options

Information

Helpful: 0

Views: 9607

Replies: 6

Related Articles