35
Votes

4 way switch

 
35
Votes

4 way switch

4 way switch
4 way switch
2019-05-26 19:15:01 - last edited 2023-02-22 23:34:50
Model: Kasa  
Hardware Version:
Firmware Version:

Release a kasa four way smart switch product, or add functionality for two three way switch products to implement a four way solution. 

#1
Options
138 Reply
Re:4 way switch
2019-05-29 17:53:08 - last edited 2021-11-17 06:21:37

@septer012 

 

There are not any current plans for a 4-way switch, however it may be possible that a HS210 3-way product may work in this enviroment.  It has not been test so before purchasing and attempting we would recomend contacting an electirican for assistance.  

 

each unit has a attached Neutral and Ground wire and 2 binding screws for the travelers and one binding screw for the common wire. Installation should be like a 3-way enviroment, where the HS210 would need to be installed in switch location that provides "power" to the 4-way run,  If its plugged into a Load.  Note you only need to replace 1 switch to add smart functionoality to the switch enviorment.  

 

Best Regards 

#2
Options
Re:Re:4 way switch
2019-07-22 16:19:37 - last edited 2021-11-17 06:21:37

i have installed 1/2 of a 3 way kit into a 4-way light.  the switch does work correctly via the paddles or the app.  however, the app doesn't know if the light is on or off.  the app always inidcates the light is off.  the switch is connected to the load end of the circuit.  maybe the switches talk to each other via wi-fi and w/o any communication the default is off?  if it was load or voltage sensing this it should know.

#3
Options
Re:Re:Re:4 way switch
2019-07-23 21:46:33 - last edited 2021-11-17 06:21:37

update.  i replaced both of the 3-way switches with TP smart switches and left the 4-way "dumb" switch in the circuit.  This set up is working perfectly for me.

#4
Options
Re:Re:Re:Re:4 way switch
2019-07-27 18:23:04 - last edited 2021-11-17 06:21:37

Board4mic, 

 

Can you clarify the setup you used, are all three switches in the 4-way circuit the TP-Link smart 3-way switches? Or just two of them with a standard switch at one of the locations?

#5
Options
Re:Re:Re:Re:Re:4 way switch
2019-07-28 01:03:24 - last edited 2021-11-17 06:21:37

when wiring a 4 way light, you have to use two 3-way switches (HS-210 kit) and one 4-way switch.  the 4-way switch solely has 2 traveler wires coming into it and 2 travelers going out of it.  i replaced the two 3-way switches with the TP link HS-210 switches.  i left the center 4-way switch as it was.  i've included a diagram to help clarify.  so in the picture i replaced the two outside switches.

#6
Options
Re:Re:Re:Re:Re:Re:4 way switch
2019-07-30 02:37:18 - last edited 2021-11-17 06:21:37

Thank you, that is very helpful! 

#7
Options
Re:Re:4 way switch
2020-01-18 01:49:51 - last edited 2021-11-17 06:21:37

@board4mic  What happened when you installed the 2nd 3-way switch? My guess would be the app recognized the light being on or off.

 

#8
Options
Re:Re:4 way switch
2020-01-20 16:53:13 - last edited 2021-11-17 06:21:37

@Mike1960   that's correct!

#9
Options
Re:Re:4 way switch
2020-02-09 00:07:44 - last edited 2021-11-17 06:21:37

@board4mic So at the risk of sounding obtuse, the 1 regular 4-way and 2 Kasa 3-way swicthes works exactly as one would hope:

The app knows if the light is on/off 

The app correctly turns on or off as per request/

Any switch can change the state at any time

 

Correct?

And thus, in the case you wanted to have 4 or more stations, all the addditional switches would be 4-way?

 

#10
Options
Re:4 way switch
2020-02-20 18:54:28 - last edited 2021-11-17 06:21:37

CONFIRMED WORKING FOR BOTH 4 AND 5 WAY INSTALLATIONS IN MY HOUSE.

I can confirm that a single HS210 kit (with 2 switches in it) worked for both my 4 and 5 way switch configurations.  They should be installed in the "3-way" switch boxes present in each configuration.  I'm not positive which boxes those are or exactly the layout of the wiring as my electrician installed them for me, but an electrican can tell you.  Basically the 2 boxes with the least wires in each case.  For the other switch locations you use normal dumb switches (the Kasa switches will know the on/off state from the presence of power at one of the switches).

 

A KEY POINT: In order for this to work correctly, you have to set the switches as a pair in the software.  This means you only add ONE SWITCH initally, and then you must choose the "installing 2 switches" option during the set up of that first switch.  It will then have you go to the second switch and hold the button down till the red light flashes.  Once this is done, the two switches show up as a single switch in the software.  They are then able to communicate back and forth if they see power and thus mark the switch as on or off.    If you fail to do this, you will have a number of issues related to turning the lights on and off programatically.  If you do this wrong and you see two switches listed in the software, you must go back and delete both switches and start over.

 

Great job TP-Link for such a flexible product.

 

#11
Options

Information

Helpful: 35

Views: 109586

Replies: 138

Voters 23

voter's avatar
voter's avatar
voter's avatar
voter's avatar
+ 19 Voters