Business Router Forums - Business Community

Want to route server on a sub-LAN to a particular WAN

I have two WANs. On the LAN side I have the ER605 serving IP addresses (192.168.0.xx) to a number of devices. One of these is a Mesh network, which has its own router and subnet (192.168.5.xx). I have

VLAN & Multi-NetworksLoad BalancingDHCP Service

By rtX · Latest post 2022-09-24 21:51:22 by btx

0Helpful

794Views

11Replies

How to guarantee bandwidth

Hello, On our older router (TL-ER6020) I could guarantee bandwidth for our voip phones, but this ER7206 only has a cap option rather than a guaranteed option under the Bandwidth Control section of the

Load Balancing

By JasonPamir · Latest post 2022-09-19 07:42:46 by Somnus

0Helpful

165Views

1Replies

ER605 for dual WAN load balance and failover?

Hi. I have a 250 Mb connection and a 45 Mb connection. Will ER605 be able to successfully provide load balance and failover (incase one WAN fails) without any throttling? I am using Mikrotik rb750gr3

Load BalancingVLAN & Multi-Networks

By kashif789us · Latest post 2022-09-11 00:42:46 by kashif789us

3Helpful

1662Views

6Replies

Detected Large ping attack. Dropped x packets

Hello I have 3 internet line the router is TL-ER5120 in system log i see a lot of this message Detected Large ping attack. Dropped x packets. and the internet is very slow in Traffic Statistics i see

Load Balancing

By Aabed · Latest post 2022-09-08 08:39:25 by Virgo

2Helpful

963Views

2Replies

Virtual-Server and One-to-one NAT failures and hairpin/loopback issues

I have experimented quite a bit with both features. I have 13 static IPs from my ISP. They work just fine outside ER7206 (WAN) side. I started with firmware 1.2.1 Reading through all the firmware patc

Firmware UpdateLoad BalancingNATVLAN & Multi-Networks

By smallscript

1Helpful

269Views

0Replies

Best load balancing mode for double WAN 4G + VDSL

Hi all, I would like to ask for the recommended configuration of load balancing for the following situation: I have a cable internet connection with 1Mbps Upload that works fine for navigation and low

Load Balancing

By leki389 · Latest post 2022-09-01 05:56:20 by Somnus

0Helpful

176Views

1Replies

TL-ER7206 - two WAN with same subnet (and even IP address)

Hi. A quick technical question - will two (or more) WAN connections on same logical subnet work in load-balancing mode? For example - WAN1 has 192.168.10.10/24 and WAN2 has the same? And i can't confi

VLAN & Multi-NetworksLoad Balancing

By n0p · Latest post 2022-08-19 21:19:38 by MaximusMark

0Helpful

635Views

2Replies

ER7206 - Multi-ISP setup not working properly

Hi there, I bought the router to get at least a decent fail-over option and if possible increase the total speed for multiple clients. 1.00 gig ISP1 0.25 gig ISP2 my dream would be, if ISP1 could be u

Load Balancing

By RobertMEF · Latest post 2022-08-11 12:16:37 by RobertMEF

0Helpful

717Views

7Replies

Bandwidth control with Load Balance on ER605 - how does it work?

I use ER605 (still on v1.1.1) in standalone mode with 2 WAN ports. These two internet connections have identical bandwidth plan. I have set up Bandwidth Control when usage reaches a certain percentage

Load BalancingBandwidth Control

By Arion · Latest post 2022-08-09 19:59:02 by Arion

1Helpful

1240Views

4Replies

Tp Link R470T+ only connecting to Backup WAN in failover mode

I have 2 Internet connections : 1) FTTH and 2) 4G (via ethernet on separate router). I have configured the TL-R470T+ router as a failover wherein the backup wan shall connect when any primary WAN fail

Load BalancingVLAN & Multi-Networksfailover

By TanayNemade · Latest post 2022-08-02 06:53:02 by Virgo

0Helpful

247Views

1Replies